Sun Microsystems LSI22320-SR manual Testing the Host Adapter

Page 19

Testing the Host Adapter

You should test the host adapter installation using the probe-scsi-allcommand and, if the newly attached device is a disk array, with the SunVTS software.

▼To Test the Installation Using the probe-scsi- all Command

1.If you have disconnected the power cable, reconnect it.

2.Power on the connected storage device(s) and then power on the host.

3.Bring the system down to the ok prompt at run level 0.

Note – If the host starts to reboot, interrupt the reboot process by pressing the Stop and A keys simultaneously.

4.At the ok prompt, enter the probe-scsi-allcommand to verify that the system recognizes the host adapter.

The probe-scsi-allcommand displays the SCSI devices connected to the host, as shown in the following screen example.

ok probe-scsi-all

/pci@4,2000/pci@1/scsi@2 Target 0

Unit 0 DISK SEAGATE ST336605LSUN36G 0238 /pci@4,2000/pci@1/scsi@2,1

Target 0

Unit 0 DISK SEAGATE ST336605LSUN36G 0238

In this example, the first SCSI port (scsi@2) has one disk drive connected

(Target 0). The second SCSI port (scsi@2,1) also has one disk drive connected (Target 0). In the illustration of the host adapter in Figure 1-1, the first SCSI port is labeled as Channel A; the second SCSI port as Channel B.

Chapter 1 Installing, Connecting, and Testing the Host Adapter 9

Image 19

Contents Sun Microsystems, Inc Please Recycle Contents Specifications Before You Read This Book PrefaceHow This Book Is Organized Using Unix CommandsRelated Documentation Typographic ConventionsTo Access the Release Notes Accessing Sun DocumentationRight frame, under Use, click Documentation Contacting Sun Technical Support Third-Party Web SitesSun Welcomes Your Comments Page Installing, Connecting, and Testing the Host Adapter 1Sun StorEdge PCI/PCI-X Dual Ultra320 Scsi Host Adapter FeaturesInstalling the Host Adapter Exit the operating environment To Prepare for Hardware InstallationInstall any required driver patches on the host Install the SunVTS software on the hostChoose a PCI-X or PCI slot for installing the host adapter Unpack the host adapter Remove the wrist strap Close the system To Install the Host AdapterOpen the system Remove the filler panel for the desired slotConnecting the Host Adapter To Test the Installation Using the probe-scsi- all Command Testing the Host AdapterAs superuser, open the SunVTS window To Test the Installation With the SunVTS SoftwareBooting the Host Adapter Page Target Devices Ultra320 Scsi ConfigurationTable A-1Bus Restrictions Bus LengthCabling Cabling and TerminationTermination LVD LVD/MSE HVD Scsi SymbolsPhysical Dimensions SpecificationsPerformance Specifications Power RequirementsPCI Edge Connector Pin Definitions Trst Vhdci Connector Internal Scsi Connector Scsi Connector Pin Definitions+ATN P E N D I X C Declaration of Conformity Appendix C Declaration of Conformity FCC Class a Notice Regulatory Compliance StatementsModifications to Equipment Safety Agency Compliance StatementsSymbols Placement of a Sun Product Noise LevelSystem Unit Cover Power Cord ConnectionBattery Warning Selv ComplianceCD and DVD Devices SymbolesRack System Warning Laser Compliance NoticeConformité Selv Modification du matérielConnexion du cordon d’alimentation Périphériques CD et DVD Mise en garde relative aux batteries Couvercle de lunitéAvis de conformité des appareils laser Mise en garde relative au système en rackAufstellung von Sun-Geräten SymboleSicherheitsvorkehrungen Modifikationen des GerätsWarnungen bezüglich in Racks eingebauter Systeme Anschluss des NetzkabelsWarnung bezüglich Batterien GehäuseabdeckungSímbolos Hinweis zur Laser-KonformitätCD- und DVD-Geräte Medidas de seguridadCumplimiento de la normativa para instalaciones Selv Modificaciones en el equipoColocación de un producto Sun Nivel de ruidoAdvertencia sobre el sistema en bastidor Advertencia sobre las bateríasCubierta de la unidad del sistema Norge Sverige Dispositivos de CD y DVDDanmark Suomi