Patton electronic 3202 manual Installing the Model, Location and mounting requirements

Page 29

Model 3202 Getting Started Guide	3 • Hardware installation

Note When setting up your Model 3202 you must consider cable-length limitations and potential electromagnetic interference (EMI) as deﬁned by the applicable local and international regulations. Ensure that your site is properly prepared before beginning installation.

Location and mounting requirements

The Model 3202 is intended to be placed on a desktop or similar sturdy, ﬂat surface that offers easy access to the cables. Additionally, you should consider the need to access the unit for future upgrades and maintenance.

This completes the planning phase for installation. The next section begins the installation procedures.

Installing the Model 3202

Unpacking the Model 3202

Inspect the shipping carton for external damage. Note any damage before removing the container contents. Report any equipment damage to the shipping carrier immediately for claim purposes. Save all packing mate- rial in case you need to return an item to the factory for servicing.

The Model 3202 comes with the following items:

•Model 3202 Quick Start Guide

•Model 3202

•An RJ-45-to-RJ-45 cable for use with the console and Ethernet ports

•A DB-9-to-RJ-45 (EIA-561) adapter for connecting a PC’s serial port to the Model 3202 console port

•CD-ROM containing product literature and the Model 3202 Getting Started Guide

Note Power cables are shipped separately from the Model 3202

Connecting cables

		The Interconnecting cables must be acceptable for external use
		and must be rated for the proper application with respect to volt-
	CAUTION	age, current, anticipated temperature, ﬂammability, and
	CAUTION	mechanical serviceability.
		mechanical serviceability.

1.Connect the Ethernet cable to the MGMT port. Model 3202 supports audi-MDIX switching so you may use a crossover or straight-through cable.

2.Connect one end of a phone cable to the LINE port and the other end of the cable to a wall jack.

Do not work on the system or connect or disconnect cables during periods of lightning activity.

WARNING

Installing the Model 3202

29

Image 29

Contents RocketLink Model Mailsupport@patton.com Summary Table of Contents Table of Contents Web configuration Console and Telnet configuration Contacting Patton for assistance Port pin-outs List of Figures Model 3202 Getting Started Guide List of Tables Structure About this guideAudience Impaired functioning PrecautionsPreventing Electrostatic Discharge Damage Safety when working with electricityTected by a circuit breaker Model 3202 ﬁrstGeneral observations Clean the case with a soft slightly moist anti-static clothGeneral conventions Typographical conventions used in this documentGeneral information Chapter contentsModel Model 3202 overviewLED descriptions Model 3202 front panelWAN 1-4 Link LAN 1-4100MDC 9V 2A Model 3202 rear panelPort descriptions Ground terminal Reset buttonApplications overview Typical application IntroductionDistance Chart Model 3202/4W 4 Wire/2 Pair Distance chartsDistance Chart 3200 Series Per Wire Pair Distance Chart Model 3202/8W 8 Wire/4 Pair Hardware installation Planning the installation IP related information Network diagramAC Power Mains Connecting cables Installing the ModelLocation and mounting requirements Unpacking the ModelGrounding stud Grounding the Model 3202 and connecting powerWeb conﬁguration requirements Conﬁguring the ModelConsole conﬁguration requirements Telnet conﬁguration requirementsWeb conﬁguration Web configuration System Login Setting Up the WMITCP/IP setup Basic Conﬁguration Options Operation mode and Mgmt portDhcp server Subnet Mask Host Name SohoLAN IP Address Subnet Mask Gateway DNS Server 1 DNS Server 2 Review and save basic setup changesAnnex Type Advanced Conﬁguration OptionsLine Type Tcpam Type Wire modelMain Rate SNR MarginVlan VID 1Q Tag-Based Vlan 802.1Q Tag-Based Vlan802.1Q Vlan Web configuration Port-Based Vlan Port-Based VlanTpid Tag Protocol Identiﬁer Enter 33024 for IEEE802.1Q Port-Based QinQQuality of Service QoS QoS Port Based Priority Port Based PriorityQoS Vlan Tag Priority Vlan Tag PriorityDefault IP Dscp Priority Service by WRRStays the same link layer and routing protocol keep alive Delay NormalClass Throughput Normal High ReliabilityQoS IP Dscp Priority Rate Control Rate ControlMgmt Status Status OptionsLine Status LAN Status Administration OptionsSecurity Administration Remote Management Hosts User ProﬁlesSnmp Administration Snmp AdministrationSnmp community pool conﬁguration Community PoolSystem Information Utility OptionsTrap Host Pool Conﬁguration Tool Conﬁguration ToolLogout UpgradeRestart RestartDhcp Server Dhcp Fixed Host DNS Proxy Host Name Console and Telnet conﬁgurationConsole and Telnet configuration Interface commands Log in using TelnetCtrl + C Quit conﬁguring the item Ctrl +Q Access help Log in to the console interfaceConsole/Telnet Menu Window structureMenu tree for authorized users Main Menu TreeMain screen for authorized users Menu tree for unauthorized usersEnable Command Menu Setup Command Menu Maximum Main Rate ModeLink IP Address Subnet Mask ClearVlan Mode Setup Command Menu Pvid QoS QoS ModeQueue Schedule Queue WeightQoS Mode Weight Value Vlan Tag Priority QoS Port-Based Priority QoSVlan Tag Index 0 1 2 3 4 5 6 Queue Index IP Dscp Priority QoSRate ListPort Port SnifﬁngMgmt Dhcp Fixed Host Dhcp ServerHost Name Factory DefaultDNS Proxy Shdsl Status Status Command MenuInterface Status ShdslWrite Command Show Command MenuSystem ConﬁgPing Command Reboot CommandModify/Add User Administration Command MenuUser Proﬁle Legal IP Address Pool SecurityTelnet TCP Port Community SnmpReadOnly Trap hostReadWrite DeniedSupervisor ID Supervisor Password and IDSupervisor Password Upgrade main software Utility Command MenuBackup system conﬁguration Restore system conﬁgurationExit Command Contacting Patton for assistance Contact information Warranty coverageReturns for credit Out-of-warranty serviceReturn for credit policy RMA numbersAppendix a Compliance information Radio and TV interference FCC Part ComplianceCE Declaration of Conformity Authorized European RepresentativeAppendix B Speciﬁcations Ethernet Connector Shdsl ConnectorManagement Connector Shdsl SpeciﬁcationsPower Supply Front Panel IndicatorsDimensions WeightAppendix C Port pin-outs EIA-561 RJ-45 8-pin port Console portEthernet