Patton electronic 3202 manual Reboot Command, Ping Command

Page 88

Model 3202 Getting Started Guide5 • Console and Telnet configuration

Reboot Command

The reboot command restarts the Model 3202. Move the cursor “ >>” to reboot in the main menu and press Enter.

----------------------------------------------------------------------

Command: reboot <CR>

Message: Please input the following information.

Do you want to reboot? (y/n): y

----------------------------------------------------------------------

Type “y” to begin the reboot process.

Ping Command

The ping command checks the connection of the Model 3202 to the network. Move the cursor “ >>” to ping in the main menu and press Enter.

The ping command sends an echo request packet to an address, and then waits for reply. The ping output can help you evaluate path-to-host reliability, delays over the path, and whether the host can be reached or is func- tioning correctly.

----------------------------------------------------------------------

Command: ping <ip> [1~65534-t] [1~1999]

Message: Please input the following information.

IP address <IP> : 10.0.0.1

Number of ping request packets to send (TAB select): -t

Data size [1~1999]: 32

----------------------------------------------------------------------

There are 3 parameters for the ping command:

•IP address: Enter the IP address that you want to ping.

•Number of ping request packed to send: Use the TAB key to select the following options.

-Default: Sends 4 packets only

-1~65534: Sets the number of ping request packets from 1 to 65534

--t :Results run continuously until you press the Ctrl key to stop the process

•Data Size: Select from 1 to 1999

Reboot Command

88

Image 88

Contents RocketLink Model Mailsupport@patton.com Summary Table of Contents Table of Contents Web configuration Console and Telnet configuration Contacting Patton for assistance Port pin-outs List of Figures Model 3202 Getting Started Guide List of Tables Audience About this guideStructure Precautions Impaired functioningSafety when working with electricity Preventing Electrostatic Discharge DamageTected by a circuit breaker Model 3202 ﬁrstClean the case with a soft slightly moist anti-static cloth General observationsTypographical conventions used in this document General conventionsChapter contents General informationModel 3202 overview ModelModel 3202 front panel LED descriptionsWAN 1-4 Link LAN 1-4100MPort descriptions Model 3202 rear panelDC 9V 2A Reset button Ground terminalApplications overview Introduction Typical applicationDistance Chart 3200 Series Per Wire Pair Distance chartsDistance Chart Model 3202/4W 4 Wire/2 Pair Distance Chart Model 3202/8W 8 Wire/4 Pair Hardware installation Planning the installation AC Power Mains Network diagramIP related information Installing the Model Connecting cablesLocation and mounting requirements Unpacking the ModelGrounding the Model 3202 and connecting power Grounding studConﬁguring the Model Web conﬁguration requirementsConsole conﬁguration requirements Telnet conﬁguration requirementsWeb conﬁguration Web configuration TCP/IP setup Setting Up the WMISystem Login Operation mode and Mgmt port Basic Conﬁguration OptionsSubnet Mask Host Name Soho Dhcp serverLAN Review and save basic setup changes IP Address Subnet Mask Gateway DNS Server 1 DNS Server 2Line Type Advanced Conﬁguration OptionsAnnex Type Wire model Tcpam TypeMain Rate SNR MarginVlan VID 802.1Q Tag-Based Vlan 1Q Tag-Based Vlan802.1Q Vlan Web configuration Port-Based Vlan Port-Based VlanPort-Based QinQ Tpid Tag Protocol Identiﬁer Enter 33024 for IEEE802.1QQuality of Service QoS Port Based Priority QoS Port Based PriorityVlan Tag Priority QoS Vlan Tag PriorityDefault Service by WRR IP Dscp PriorityDelay Normal Stays the same link layer and routing protocol keep aliveClass Throughput Normal High ReliabilityQoS IP Dscp Priority Rate Control Rate ControlLine Status Status OptionsMgmt Status Security Administration Administration OptionsLAN Status User Proﬁles Remote Management HostsSnmp Administration Snmp AdministrationCommunity Pool Snmp community pool conﬁgurationTrap Host Pool Utility OptionsSystem Information Conﬁguration Tool Conﬁguration ToolUpgrade LogoutRestart RestartConsole and Telnet conﬁguration Dhcp Server Dhcp Fixed Host DNS Proxy Host NameConsole and Telnet configuration Log in using Telnet Interface commandsCtrl + C Quit conﬁguring the item Ctrl +Q Access help Log in to the console interfaceWindow structure Console/Telnet MenuMain Menu Tree Menu tree for authorized usersMenu tree for unauthorized users Main screen for authorized usersEnable Command Menu Setup Command Menu Link ModeMaximum Main Rate Clear IP Address Subnet MaskVlan Mode Setup Command Menu Pvid QoS Mode QoSQoS Mode Weight Value Queue WeightQueue Schedule Port-Based Priority QoS Vlan Tag Priority QoSIP Dscp Priority QoS Vlan Tag Index 0 1 2 3 4 5 6 Queue IndexList RatePort Port SnifﬁngMgmt Dhcp Server Dhcp Fixed HostDNS Proxy Factory DefaultHost Name Status Command Menu Shdsl StatusInterface Status ShdslShow Command Menu Write CommandSystem ConﬁgReboot Command Ping CommandUser Proﬁle Administration Command MenuModify/Add User Telnet TCP Port SecurityLegal IP Address Pool Snmp CommunityTrap host ReadOnlyReadWrite DeniedSupervisor Password Supervisor Password and IDSupervisor ID Utility Command Menu Upgrade main softwareBackup system conﬁguration Restore system conﬁgurationExit Command Contacting Patton for assistance Warranty coverage Contact informationOut-of-warranty service Returns for creditReturn for credit policy RMA numbersAppendix a Compliance information Compliance Radio and TV interference FCC PartCE Declaration of Conformity Authorized European RepresentativeAppendix B Speciﬁcations Shdsl Connector Ethernet ConnectorManagement Connector Shdsl SpeciﬁcationsFront Panel Indicators Power SupplyDimensions WeightAppendix C Port pin-outs Console port EIA-561 RJ-45 8-pin portEthernet