Patton electronic 3202 Log in to the console interface, Log in using Telnet, Interface commands

Page 67

Model 3202 Getting Started Guide

5 • Console and Telnet configuration

 

 

Introduction

This chapter provides information for configuring the Model 3202 by using the serial console with Telnet.

Log in to the console interface

The console port is a RJ-48C connector that provides a connection to a PC for monitoring and configuring the Model 3202. Use the supplied serial cable with a female DB-9 connector to connect to the serial port of PC, and connect the RJ-48C module jack connector to the Model 3202's console port. Start your terminal emulation program (such as Hyper Terminal) and configure the communication parameters. Use the settings shown in Table 15 to log into the console:

Table 15. Console settings

Parameter

Value

 

 

Baud rate

9600

 

 

Data Bits

8

 

 

Parity Check

None

 

 

Stop Bits

1

 

 

Flow-control

None

 

 

After you enter the settings for the console, press the spacebar until the login screen appears. When you see the login screen, you can log on to the Model 3202. Enter admin for both the User Name and Password.

Log in using Telnet

The Model 3202 also supports Telnet for remote management. Connect the Ethernet cable to the MGMT port of Model 3202 to your computer. The MGMT LED on the front panel of the Model 3202 will light up. Start your Telnet client with VT100 terminal emulation and connect to the management IP of the Model 3202. Wait for the login prompt to display. Enter your user name and password. When you see the login screen, you can log on to the Model 3202. Enter admin for both the User Name and Password.

Note The default IP address is 192.168.1.1. The line command is “telnet 192.168.1.1” in DOS mode.

Interface commands

Before changing the configuration, familiarize yourself with the operations list in the following table:

Table 16. Interface commands

Keystroke

Description

 

 

[UP] or I

Move to the field above in the same level menu.

 

 

[DOWN] or K

Move to field below in the same level menu.

 

 

[LEFT] or J

Move back to the previous menu.

 

 

[RIGHT], L or [ENTER]

Move forward to the submenu.

 

 

[HOME] or U

Move to the first field.

 

 

[END] or O

Move to the last field.

 

 

[TAB]

Choose another parameter.

 

 

Ctrl + C

Quit configuring the item.

 

 

Ctrl +Q

Access help.

 

 

Introduction

67

Image 67
Contents RocketLink Model Mailsupport@patton.com Summary Table of Contents Table of Contents Web configuration Console and Telnet configuration Contacting Patton for assistance Port pin-outs List of Figures Model 3202 Getting Started Guide List of Tables Audience About this guideStructure Impaired functioning PrecautionsModel 3202 first Safety when working with electricityPreventing Electrostatic Discharge Damage Tected by a circuit breakerGeneral observations Clean the case with a soft slightly moist anti-static clothGeneral conventions Typographical conventions used in this documentGeneral information Chapter contentsModel Model 3202 overviewLAN 1-4100M Model 3202 front panelLED descriptions WAN 1-4 LinkPort descriptions Model 3202 rear panelDC 9V 2A Ground terminal Reset buttonApplications overview Typical application IntroductionDistance Chart 3200 Series Per Wire Pair Distance chartsDistance Chart Model 3202/4W 4 Wire/2 Pair Distance Chart Model 3202/8W 8 Wire/4 Pair Hardware installation Planning the installation AC Power Mains Network diagramIP related information Unpacking the Model Installing the ModelConnecting cables Location and mounting requirementsGrounding stud Grounding the Model 3202 and connecting powerTelnet configuration requirements Configuring the ModelWeb configuration requirements Console configuration requirementsWeb configuration Web configuration TCP/IP setup Setting Up the WMISystem Login Basic Configuration Options Operation mode and Mgmt portDhcp server Subnet Mask Host Name SohoLAN IP Address Subnet Mask Gateway DNS Server 1 DNS Server 2 Review and save basic setup changesLine Type Advanced Configuration OptionsAnnex Type SNR Margin Wire modelTcpam Type Main RateVlan VID 1Q Tag-Based Vlan 802.1Q Tag-Based Vlan802.1Q Vlan Web configuration Port-Based Vlan Port-Based VlanTpid Tag Protocol Identifier Enter 33024 for IEEE802.1Q Port-Based QinQQuality of Service QoS QoS Port Based Priority Port Based PriorityQoS Vlan Tag Priority Vlan Tag PriorityDefault IP Dscp Priority Service by WRRThroughput Normal High Reliability Delay NormalStays the same link layer and routing protocol keep alive ClassQoS IP Dscp Priority Rate Control Rate ControlLine Status Status OptionsMgmt Status Security Administration Administration OptionsLAN Status Remote Management Hosts User ProfilesSnmp Administration Snmp AdministrationSnmp community pool configuration Community PoolTrap Host Pool Utility OptionsSystem Information Configuration Tool Configuration ToolLogout UpgradeRestart RestartDhcp Server Dhcp Fixed Host DNS Proxy Host Name Console and Telnet configurationConsole and Telnet configuration Log in to the console interface Log in using TelnetInterface commands Ctrl + C Quit configuring the item Ctrl +Q Access helpConsole/Telnet Menu Window structureMenu tree for authorized users Main Menu TreeMain screen for authorized users Menu tree for unauthorized usersEnable Command Menu Setup Command Menu Link ModeMaximum Main Rate IP Address Subnet Mask ClearVlan Mode Setup Command Menu Pvid QoS QoS ModeQoS Mode Weight Value Queue WeightQueue Schedule Vlan Tag Priority QoS Port-Based Priority QoSVlan Tag Index 0 1 2 3 4 5 6 Queue Index IP Dscp Priority QoSPort Sniffing ListRate PortMgmt Dhcp Fixed Host Dhcp ServerDNS Proxy Factory DefaultHost Name Shdsl Status Command MenuShdsl Status Interface StatusConfig Show Command MenuWrite Command SystemPing Command Reboot CommandUser Profile Administration Command MenuModify/Add User Telnet TCP Port SecurityLegal IP Address Pool Community SnmpDenied Trap hostReadOnly ReadWriteSupervisor Password Supervisor Password and IDSupervisor ID Restore system configuration Utility Command MenuUpgrade main software Backup system configurationExit Command Contacting Patton for assistance Contact information Warranty coverageRMA numbers Out-of-warranty serviceReturns for credit Return for credit policyAppendix a Compliance information Authorized European Representative ComplianceRadio and TV interference FCC Part CE Declaration of ConformityAppendix B Specifications Shdsl Specifications Shdsl ConnectorEthernet Connector Management ConnectorWeight Front Panel IndicatorsPower Supply DimensionsAppendix C Port pin-outs EIA-561 RJ-45 8-pin port Console portEthernet