The
|
|
| 1 | (N/C) | |||||||||||||||||||||||||
1 |
|
| 2 | (GND) | |||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 3 | ||||||
2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||
3 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 4 | |
4 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 5 | |||
5 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
6 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 6 | ||||
7 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
8 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 7 | (GND) | |
|
|
| 8 | (N/C) |
Figure 10. Model 1092ARC twisted pair line interface.
3. Proper
SIGNAL | PIN# | PIN# | SIGNAL |
TIP | 4 | TIP | |
RING | 5 | RING |
4. Proper
SIGNAL | PIN# | PIN# | SIGNAL |
Tx | 3 | Rx | |
Tx | 6 | Rx | |
Rx | 4 | Tx | |
Rx | 5 | Tx |
4.3.4 Connection to the Control Port Interface
Please refer to the Model 1001CC Control Card user manual for
cable requirements of the Control Port Interface.
5.0 OPERATION
Once the Model 1092ARC is properly configured and installed, it should operate transparently. This sections describes functions of the LED status indicators, and the use of the
5.1LED STATUS INDICATORS
The Model 1092ARC features twelve front panel LEDs that monitor
power, the DTE signals, network connection and test modes. Figure 11(below) shows the front panel location of each LED. Following Figure 11 is a description of each LED function.
Model 1092ARC
Figure 11. The Model 1092ARC Series' front panel LEDs
Note: LEDs described as yellow are red in earlier versions of the 1092ARC.
TD & RD | glow yellow to indicate an idle condition of Binary |
| “1” data on the respective terminal interface |
| signals. Green indicates Binary “0” data. |
CTS | consists of 2 LEDs, 1 yellow, 1 green. CTS glows |
| green to indicate that the Clear to Send signal from |
| the modem is active. Yellow indicates inactive |
| CTS. |
CD | consists of 2 LEDs, 1 yellow, 1 green. CD glows |
| yellow if no carrier signal is being received from the |
| remote modem. Green indicates that the remote |
| modem’s carrier is being received. |
DTR | glows green to indicate that the Data Terminal |
| Ready signal from the terminal is active. |
29 | 30 |
|