Table
1- 2 - 3 - 4 - 5 - 6 - 7 - 8 - 9 - 10 - 11 - 12 - 13 - NMS - PS2 - PS1
The following table
address.
Table
| Upper (Lower) Nibble |
|
|
|
| |||||||
|
|
|
|
| ||||||||
0 |
|
| ON | ON |
| ON |
|
| ON | |||
| 1 |
|
| ON | ON |
| ON |
|
| OFF | ||
2 |
|
| ON | ON |
| OFF |
| ON | ||||
3 |
|
| ON | ON |
| OFF |
|
| OFF | |||
4 |
|
| ON | OFF |
| ON |
| ON | ||||
|
|
|
|
|
|
|
|
|
|
|
| |
5 |
|
| ON | OFF |
|
| ON |
| OFF | |||
6 |
|
| ON | OFF |
| OFF |
| ON | ||||
7 |
|
| ON | OFF |
| OFF |
| ON | ||||
8* |
|
| OFF | ON |
| ON |
| ON | ||||
| 9* |
|
| OFF | ON |
| ON |
| OFF | |||
| A* | OFF | ON |
| OFF |
| ON | |||||
|
|
|
|
|
|
|
|
|
|
| ||
| B* | OFF | ON |
| OFF |
| OFF | |||||
| C* | OFF | OFF |
| ON |
| ON | |||||
|
|
|
|
|
|
|
| |||||
| D* | OFF | OFF |
| ON |
| OFF | |||||
| E* | OFF | OFF |
| OFF |
| ON | |||||
| F* |
|
| OFF | OFF |
| OFF |
|
| OFF | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
* 8 - F are only available for Lower Nibble.
Address |
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
| ||||||||
(Dec.) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
0x01 (1) |
| ON |
| ON |
| ON |
| ON |
| ON |
| ON |
| OFF |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
0x10 (16) |
| ON |
| ON |
| OFF |
| ON |
| ON |
| ON |
| ON |
0x35 (53) |
| ON |
| OFF |
| OFF |
| ON |
| OFF |
| ON |
| OFF |
3.1.4 Configuration Switch Set “S5”
The configuration switches on S5 allow you to specify the data rate,
Switch
S5 SUMMARY TABLE
| Position | Function | Factory Default |
|
| |
|
|
|
|
|
|
|
| Data Rate | Off |
|
|
| |
|
|
|
|
|
|
|
| Off |
|
| |||
|
|
|
|
|
|
|
| Enable LAL or RDL from DTE | On | Enable |
|
| |
|
|
|
|
|
|
|
| Front Panel Switch Control | Off | Enable |
|
| |
|
|
|
|
|
|
|
Use Switch
11
Switch S5-2: 2-Wire/4-Wire
Use Switch
Setting | Description | |
Off | ||
On |
Switch S5-3: Enable LAL and RDL from DTE
Use Switch
Setting | Description | |
On | Enabled | LAL and RDL enabled |
Off | Disabled | LAL and RDL disabled |
Switch S5-4: Enable Front Panel Swtiches
Use Switche
Setting | Description | |
On | Enabled | Front Panel Switches |
|
| enabled. |
Off | Disabled | Front Panel Switches |
|
| disabled. |
3.2CONFIGURE THE SOFTWARE SWITCHES
The Model 1092ARC features a menu-driven command system
that allows you to configure the local 1092ARC. The software control port signals of the 1092ARC are carried to each card in the rack along the internal power bus board. Access to all rack card control ports is provided by a single PATTON Model 1001CC Control Card (see Model Model 1001CC User Manual). After setting the control port address (Section 3.1.3), use the following instructions to configure the unit:
1)Connect the serial
2)Power up the terminal and set its
8 data bits, 1 stop bit, no parity Local echo
3.Press [CTRL+B] on the terminal followed by the
12