|
| TABLE OF CONTENTS |
|
| Section | Page | |
1.0 | Warranty Information | 2 | |
| 1.1 | Radio and TV Interference |
|
| 1.2 | CE Notice |
|
| 1.3 | Service Information |
|
2.0 | General Information | 4 |
2.1Features
2.2Description
2.3SNMP Management Soulutions
3.0 Configuration | .........................................................................6 |
3.1Configure the Hardware Switches
3.1.1Reversible Interface Driver Board
3.1.2Configuration Switch Set “S1”
3.1.3Configuration Switch Set “S2”
3.1.4Configuration Switch Set “S3”
3.2Configure the Software Switches
3.2.1Configure the Local 1092ARC
3.3Configure the Rear Interface Card
3.3.1Model 1001RCM12545 Rear Card Strap Settings
3.3.2Model 1001RCM13445 Rear Card Strap Settings
3.3.3Model 1001RCM11545 Rear Card Strap Settings
4.0 Installation | ...........................................................................26 |
4.1The Model 1001R14P Rack Chassis
4.1.1The Rack Power Supply
4.2Install the Model 1092ARC Series Into Chassis
4.3Wire the Model 1092ARC Series
4.3.1Connect to a “DTE” Device
4.3.2Connect to a “DCE” Device
4.3.3Connect the Twisted Pair Interface
4.3.4Connection to the Control Port Interface
5.0 Operation | .............................................................................30 |
5.1LED Status Indicators
5.2Test Modes
5.2.1Local Line Loopback (LLB)
5.2.2Remote Digital Loopback (RDL)
5.2.3V.52 (BER) Test Pattern Generator
Appendix A - Factory Replacement Parts and Accessories | 34 |
Appendix B - V.35 Terminal Interface Pin Assignments | 35 |
- | 36 |
Appendix C - Control Port Pin Assignments | 37 |
Appendix D - Line Interface Pin Assignments | 38 |
1
1.0 WARRANTY INFORMATION
Patton Electronics warrants all Model 1092ARC components to be free from defects, and will— at our option— repair or replace the product should it fail within one year from the first date of shipment.
This warranty is limited to defects in workmanship or materials, and does not cover customer damage, abuse or unauthorized modification. If this product fails or does not perform as warranted, your sole recourse shall be repair or replacement as described above. Under no condition shall Patton Electronics be liable for any damages incurred by the use of this product. These damages include, but are not limited to, the following: lost profits, lost savings and incidental or consequential damages arising from the use of or inability to use this product. Patton Electronics specifically disclaims all other warranties, expressed or implied, and the installation or use of this product shall be deemed an acceptance of these terms by the user.
1.1 RADIO AND TV INTERFERENCE
The Model 1092ARC generates and uses radio frequency energy, and if not installed and used properly— that is, in strict accordance with the manufacturer's instructions— may cause interference to radio and television reception. The Model 1092ARC has been tested and found to comply with the limits for a Class A computing device in accordance with the specifications in Subpart J of Part 15 of FCC rules, which are designed to provide reasonable protection from such interference in a commercial installation. However, there is no guarantee that interference will not occur in a particular installation. If the Model 1092ARC does cause interference to radio or television reception, which can be determined by disconnecting the unit, the user is encouraged to try to correct the interference by one or more of the following measures: moving the computing equipment away from the receiver,
1.2 CE NOTICE
The CE symbol on your Patton Electronics equipment indicates that it is in compliance with the Electromagnetic Compatibility (EMC) directive and the Low Voltage Directive (LVD) of the European Union (EU). A Certificate of Compliance is available by contacting Technical Support.
2