Patton electronic 2160 Series Safety when working with electricity, Tected by a circuit breaker

Page 14

Model 2160 Series Getting Started Guide	About this guide

Safety when working with electricity

The Model 2160 contains no user serviceable parts. The equipment shall be returned to Patton Electronics for repairs, or repaired by qualiﬁed service per- sonnel. Opening the Model 2160 case will void the warranty.

WARNING

Mains Voltage: Do not open the case the when the power cord is attached. Line voltages are present within the power supply when the power cords are

connected. The mains outlet that is utilized to power the device shall be WARNING within 10 feet (3 meters) of the device, shall be easily accessible, and pro-

tected by a circuit breaker.

For AC powered units, ensure that the power cable used meets all applicable standards for the country in which it is to be installed, and that it is connected to a wall outlet which has earth ground.

	WARNING
		Hazardous network voltages are present in WAN ports regardless of whether
		power to the Model 2160 is ON or OFF. To avoid electric shock, use caution
	WARNING	when near WAN ports. When detaching the cables, detach the end away from
	WARNING	the Model 2160 ﬁrst.
		the Model 2160 ﬁrst.

Do not work on the system or connect or disconnect cables during periods of lightning activity.

WARNING

In accordance with the requirements of council directive 2002/ 96/EC on Waste of Electrical and Electronic Equipment (WEEE), ensure that at end-of-life you separate this product from other waste and scrap and deliver to the WEEE collection system in your country for recycling.

14

Image 14

Contents

CopperLink Model 2160 Series Mailsupport@patton.com Summary Table of Contents Table of Contents Web configuration Console and Telnet configuration Contacting Patton for assistance Port pin-outs List of Figures Model 2160 Series Getting Started Guide List of Tables Structure About this guideAudience Precautions Impaired functioningModel 2160 ﬁrst Safety when working with electricityTected by a circuit breaker Preventing Electrostatic Discharge Damage General observationsTypographical conventions used in this document General conventionsChapter contents General informationModel 2160 overview ModelWAN 1-4 Link Model 2160 front panelLED descriptions LAN 1-4100MModel 2160 rear panel Port descriptionsReset button Ground terminalApplications overview Introduction Typical applicationDistance charts Distance Chart 2160 Series Standard SettingDistance Chart 2160 Series High Speed Setting Hardware installation Planning the installation IP related information Network diagramAC Power Mains Location and mounting requirements Installing the ModelConnecting cables Unpacking the ModelGrounding the Model 2160 and connecting power Grounding studConsole conﬁguration requirements Conﬁguring the ModelWeb conﬁguration requirements Telnet conﬁguration requirementsWeb conﬁguration Web configuration System Login Setting Up the WMITCP/IP setup Operation mode and Mgmt port Basic Conﬁguration OptionsSubnet Mask Host Name Soho Dhcp serverLAN IP Address Subnet Mask Gateway DNS Server 1 DNS Server 2 Review and save basic setup changes Review and save basic setup changesAnnex Type Advanced Conﬁguration OptionsLine Type SNR Margin Tcpam TypeMain Rate Line ProbeVlan VID 802.1Q Tag-Based Vlan 1Q Tag-Based Vlan802.1Q Vlan Web configuration Port-Based Vlan Port-Based VlanPort-Based QinQ Tpid Tag Protocol Identiﬁer Enter 33024 for IEEE802.1QQuality of Service QoS Port Based Priority QoS Port Based PriorityVlan Tag Priority QoS Vlan Tag PriorityDefault Service by WRR IP Dscp PriorityClass Delay NormalStays the same link layer and routing protocol keep alive Throughput Normal High ReliabilityQoS IP Dscp Priority Rate Control Rate ControlMgmt Status Status OptionsLine Status LAN Status Administration OptionsSecurity Administration User Proﬁles Remote Management HostsSnmp Administration Snmp AdministrationCommunity Pool Snmp community pool conﬁgurationSystem Information Utility OptionsTrap Host Pool Conﬁguration Tool Conﬁguration ToolUpgrade LogoutRestart RestartConsole and Telnet conﬁguration Dhcp Server Dhcp Fixed Host DNS Proxy Host NameConsole and Telnet configuration Ctrl + C Quit conﬁguring the item Ctrl +Q Access help Log in using TelnetInterface commands Log in to the console interfaceWindow structure Product name Line BridgeMain Menu Tree Menu tree for authorized usersMenu tree for unauthorized users Main screen for authorized usersEnable Command Menu Setup Command Menu LineLink Wire modelMode Maximum Main RateClear IP Address Subnet MaskVlan Mode Disable 802.1Q Tag Vlan Port-Based VlanSetup Command Menu Pvid QoS Mode QoSQueue Schedule Queue WeightQoS Mode Weight Value Port-Based Priority QoS Vlan Tag Priority QoSIP Dscp Priority QoS Vlan Tag Index 0 1 2 3 4 5 6 Queue IndexPort ListRate Port LineMgmt Dhcp Server Dhcp Fixed HostHost Name Factory DefaultDNS Proxy Interface Status Command MenuInterface Status System Show Command MenuWrite Command ConﬁgReboot Command Ping CommandModify/Add User Administration Command MenuUser Proﬁle Legal IP Address Pool SecurityTelnet TCP Port Snmp CommunityReadWrite Trap hostReadOnly DeniedSupervisor ID Supervisor Password and IDSupervisor Password Backup system conﬁguration Utility Command MenuUpgrade main software Restore system conﬁgurationExit Command Contacting Patton for assistance Warranty coverage Contact informationReturn for credit policy Out-of-warranty serviceReturns for credit RMA numbersAppendix a Compliance information CE Declaration of Conformity ComplianceRadio and TV interference FCC Part Authorized European RepresentativeAppendix B Speciﬁcations Management Connector Line ConnectorEthernet Connector Line ModulationDimensions Front Panel IndicatorsPower Supply WeightAppendix C Port pin-outs Console port EIA-561 RJ-45 8-pin portEthernet Line CopperLink