Patton electronic 07M2160-GS Preventing Electrostatic Discharge Damage, General observations

Page 15

Model 2160 Series Getting Started Guide	About this guide

Preventing Electrostatic Discharge Damage

When starting to install interface cards place the interface card on its shielded plastic bag if you lay it on your bench.

Electrostatic Discharge (ESD) can damage equipment and impair electrical circuitry. It occurs when electronic printed circuit cards are improperly handled and can result in complete or intermittent failures.

Always follow ESD prevention procedures when removing and replacing cards.

CAUTION Wear an ESD-preventive wrist strap, ensuring that it makes good skin contact. Connect the clip to an unpainted surface of the chassis frame to safely channel unwanted ESD voltages

to ground.

To properly guard against ESD damage and shocks, the wrist strap and cord must operate effectively. If no wrist strap is avail- able, ground yourself by touching the metal part of the chassis.

General observations

•Clean the case with a soft slightly moist anti-static cloth

•Place the unit on a ﬂat surface and ensure free air circulation

•Avoid exposing the unit to direct sunlight and other heat sources

•Protect the unit from moisture, vapors, and corrosive liquids

15

Image 15

Contents

CopperLink Model 2160 Series Mailsupport@patton.com Summary Table of Contents Table of Contents Web configuration Console and Telnet configuration Contacting Patton for assistance Port pin-outs List of Figures Model 2160 Series Getting Started Guide List of Tables About this guide AudienceStructure Impaired functioning PrecautionsSafety when working with electricity Tected by a circuit breakerModel 2160 ﬁrst General observations Preventing Electrostatic Discharge DamageGeneral conventions Typographical conventions used in this documentGeneral information Chapter contentsModel Model 2160 overviewLAN 1-4100M Model 2160 front panelLED descriptions WAN 1-4 LinkPort descriptions Model 2160 rear panelGround terminal Reset buttonApplications overview Typical application IntroductionDistance Chart 2160 Series Standard Setting Distance chartsDistance Chart 2160 Series High Speed Setting Hardware installation Planning the installation Network diagram AC Power MainsIP related information Unpacking the Model Installing the ModelConnecting cables Location and mounting requirementsGrounding stud Grounding the Model 2160 and connecting powerTelnet conﬁguration requirements Conﬁguring the ModelWeb conﬁguration requirements Console conﬁguration requirementsWeb conﬁguration Web configuration Setting Up the WMI TCP/IP setupSystem Login Basic Conﬁguration Options Operation mode and Mgmt portDhcp server Subnet Mask Host Name SohoLAN IP Address Subnet Mask Gateway DNS Server 1 DNS Server 2 Review and save basic setup changes Review and save basic setup changesAdvanced Conﬁguration Options Line TypeAnnex Type Line Probe Tcpam TypeMain Rate SNR MarginVlan VID 1Q Tag-Based Vlan 802.1Q Tag-Based Vlan802.1Q Vlan Web configuration Port-Based Vlan Port-Based VlanTpid Tag Protocol Identiﬁer Enter 33024 for IEEE802.1Q Port-Based QinQQuality of Service QoS QoS Port Based Priority Port Based PriorityQoS Vlan Tag Priority Vlan Tag PriorityDefault IP Dscp Priority Service by WRRThroughput Normal High Reliability Delay NormalStays the same link layer and routing protocol keep alive ClassQoS IP Dscp Priority Rate Control Rate ControlStatus Options Line StatusMgmt Status Administration Options Security AdministrationLAN Status Remote Management Hosts User ProﬁlesSnmp Administration Snmp AdministrationSnmp community pool conﬁguration Community PoolUtility Options Trap Host PoolSystem Information Conﬁguration Tool Conﬁguration ToolLogout UpgradeRestart RestartDhcp Server Dhcp Fixed Host DNS Proxy Host Name Console and Telnet conﬁgurationConsole and Telnet configuration Log in to the console interface Log in using TelnetInterface commands Ctrl + C Quit conﬁguring the item Ctrl +Q Access helpProduct name Line Bridge Window structureMenu tree for authorized users Main Menu TreeMain screen for authorized users Menu tree for unauthorized usersEnable Command Menu Line Setup Command MenuMaximum Main Rate Wire modelMode LinkIP Address Subnet Mask ClearDisable 802.1Q Tag Vlan Port-Based Vlan Vlan ModeSetup Command Menu Pvid QoS QoS ModeQueue Weight QoS Mode Weight ValueQueue Schedule Vlan Tag Priority QoS Port-Based Priority QoSVlan Tag Index 0 1 2 3 4 5 6 Queue Index IP Dscp Priority QoSPort Line ListRate PortMgmt Dhcp Fixed Host Dhcp ServerFactory Default DNS ProxyHost Name Status Command Menu Interface StatusInterface Conﬁg Show Command MenuWrite Command SystemPing Command Reboot CommandAdministration Command Menu User ProﬁleModify/Add User Security Telnet TCP PortLegal IP Address Pool Community SnmpDenied Trap hostReadOnly ReadWriteSupervisor Password and ID Supervisor PasswordSupervisor ID Restore system conﬁguration Utility Command MenuUpgrade main software Backup system conﬁgurationExit Command Contacting Patton for assistance Contact information Warranty coverageRMA numbers Out-of-warranty serviceReturns for credit Return for credit policyAppendix a Compliance information Authorized European Representative ComplianceRadio and TV interference FCC Part CE Declaration of ConformityAppendix B Speciﬁcations Line Modulation Line ConnectorEthernet Connector Management ConnectorWeight Front Panel IndicatorsPower Supply DimensionsAppendix C Port pin-outs EIA-561 RJ-45 8-pin port Console portLine CopperLink Ethernet