Patton electronic 2160 Series, 07M2160-GS Show Command Menu, Write Command, System, Conﬁg, Script

Page 88

Model 2160 Series Getting Started Guide	5 • Console and Telnet configuration

Show Command Menu

The show command menu lists commands for viewing system and conﬁguration information for the Model 2160. Move the cursor “ >>” to show in the main menu and press Enter.

When you enter the show command, the following menu displays:

>> system	Show general information
config	Show all configuration
script	Show all configuration	in command script

	Table 33. Show Command Menu

Command	Description

system	Displays general system information

conﬁg	Displays detailed conﬁguration information

script	Displays conﬁguration information in command script

Move the cursor “ >>” to system in the show menu and press Enter.

Figure 53. System Information

Write Command

The write command saves all new conﬁguration changes to Flash on the Model 2160. You must use the write command and reboot the Ethernet Extender for new conﬁguration changes to tak effect. Move the cursor “ >>” to write in the main menu and press Enter.

----------------------------------------------------------------------

Command: write <CR>

Message: Please input the following information.

Are you sure? (y/n): y

----------------------------------------------------------------------

Show Command Menu

88

Image 88

Contents

CopperLink Model 2160 Series Mailsupport@patton.com Summary Table of Contents Table of Contents Web configuration Console and Telnet configuration Contacting Patton for assistance Port pin-outs List of Figures Model 2160 Series Getting Started Guide List of Tables Audience About this guideStructure Precautions Impaired functioningTected by a circuit breaker Safety when working with electricityModel 2160 ﬁrst Preventing Electrostatic Discharge Damage General observationsTypographical conventions used in this document General conventionsChapter contents General informationModel 2160 overview ModelModel 2160 front panel LED descriptionsWAN 1-4 Link LAN 1-4100MModel 2160 rear panel Port descriptionsReset button Ground terminalApplications overview Introduction Typical applicationDistance charts Distance Chart 2160 Series Standard SettingDistance Chart 2160 Series High Speed Setting Hardware installation Planning the installation AC Power Mains Network diagramIP related information Installing the Model Connecting cablesLocation and mounting requirements Unpacking the ModelGrounding the Model 2160 and connecting power Grounding studConﬁguring the Model Web conﬁguration requirementsConsole conﬁguration requirements Telnet conﬁguration requirementsWeb conﬁguration Web configuration TCP/IP setup Setting Up the WMISystem Login Operation mode and Mgmt port Basic Conﬁguration OptionsSubnet Mask Host Name Soho Dhcp serverLAN IP Address Subnet Mask Gateway DNS Server 1 DNS Server 2 Review and save basic setup changes Review and save basic setup changesLine Type Advanced Conﬁguration OptionsAnnex Type Tcpam Type Main RateSNR Margin Line ProbeVlan VID 802.1Q Tag-Based Vlan 1Q Tag-Based Vlan802.1Q Vlan Web configuration Port-Based Vlan Port-Based VlanPort-Based QinQ Tpid Tag Protocol Identiﬁer Enter 33024 for IEEE802.1QQuality of Service QoS Port Based Priority QoS Port Based PriorityVlan Tag Priority QoS Vlan Tag PriorityDefault Service by WRR IP Dscp PriorityDelay Normal Stays the same link layer and routing protocol keep aliveClass Throughput Normal High ReliabilityQoS IP Dscp Priority Rate Control Rate ControlLine Status Status OptionsMgmt Status Security Administration Administration OptionsLAN Status User Proﬁles Remote Management HostsSnmp Administration Snmp AdministrationCommunity Pool Snmp community pool conﬁgurationTrap Host Pool Utility OptionsSystem Information Conﬁguration Tool Conﬁguration ToolUpgrade LogoutRestart RestartConsole and Telnet conﬁguration Dhcp Server Dhcp Fixed Host DNS Proxy Host NameConsole and Telnet configuration Log in using Telnet Interface commandsCtrl + C Quit conﬁguring the item Ctrl +Q Access help Log in to the console interfaceWindow structure Product name Line BridgeMain Menu Tree Menu tree for authorized usersMenu tree for unauthorized users Main screen for authorized usersEnable Command Menu Setup Command Menu LineWire model ModeLink Maximum Main RateClear IP Address Subnet MaskVlan Mode Disable 802.1Q Tag Vlan Port-Based VlanSetup Command Menu Pvid QoS Mode QoSQoS Mode Weight Value Queue WeightQueue Schedule Port-Based Priority QoS Vlan Tag Priority QoSIP Dscp Priority QoS Vlan Tag Index 0 1 2 3 4 5 6 Queue IndexList RatePort Port Line Mgmt Dhcp Server Dhcp Fixed HostDNS Proxy Factory DefaultHost Name Interface Status Status Command MenuInterface Show Command Menu Write CommandSystem ConﬁgReboot Command Ping CommandUser Proﬁle Administration Command MenuModify/Add User Telnet TCP Port SecurityLegal IP Address Pool Snmp CommunityTrap host ReadOnlyReadWrite DeniedSupervisor Password Supervisor Password and IDSupervisor ID Utility Command Menu Upgrade main softwareBackup system conﬁguration Restore system conﬁgurationExit Command Contacting Patton for assistance Warranty coverage Contact informationOut-of-warranty service Returns for creditReturn for credit policy RMA numbersAppendix a Compliance information Compliance Radio and TV interference FCC PartCE Declaration of Conformity Authorized European RepresentativeAppendix B Speciﬁcations Line Connector Ethernet ConnectorManagement Connector Line ModulationFront Panel Indicators Power SupplyDimensions WeightAppendix C Port pin-outs Console port EIA-561 RJ-45 8-pin portEthernet Line CopperLink