Patton electronic 2160 Series, 07M2160-GS manual Model 2160 rear panel, Port descriptions

Page 20

Model 2160 Series Getting Started Guide	1 • General information

Model 2160 rear panel

Port descriptions

The CopperLink™ Model 2160 rear panel ports are shown in ﬁgure 3 and described in table 3.

DC	9V

CONSOLE

RST

LAN

1

2

3	MGMT
4

LINE

DC 9V				LAN
DC 9V		CONSOLE			MGMT	LINE
		CONSOLE			MGMT	LINE
		RST
+	-	1	2	3	4
		1	2	3	4


Power			Reset button

		Console			LAN (1-4)
		RS-232 port			RJ-45 port


Management			Ground
RJ-45 port
		Line
		RJ-45 port

	Figure 3. Model 2160 rear panel
		Table 3. Port descriptions

Port		Description

DC 9V		Power adaptor inlet: Input voltage 9VDC

Console (RS-232 control port)		Used for service and maintenance, the Console port, an RS-232
		RJ-45 connector with EIA-561 pinout, connects the router to a
		serial terminal such as a PC or ASCII terminal (also called a dumb
		terminal). Asynchronous default data rate 9600 bps, hardware
		DSR and DTR signals for external modems are wired directly
		together internally

RST		Reset button for rebooting or loading factory default settings

LAN (LAN Ethernet Ports 1-4)		10/100Base-Tx full-/half-duplex, RJ-45, auto detection and fall-
		back, connects the unit to an Ethernet LAN.

MGMT		RJ-45 for management port

LINE		Interface for WAN port (RJ-45)

Note For port pinout information, see Appendix C, “Port pin-outs”on page 105.

Model 2160 rear panel

20

Image 20

Contents

CopperLink Model 2160 Series Mailsupport@patton.com Summary Table of Contents Table of Contents Web configuration Console and Telnet configuration Contacting Patton for assistance Port pin-outs List of Figures Model 2160 Series Getting Started Guide List of Tables Structure About this guideAudience Precautions Impaired functioningModel 2160 ﬁrst Safety when working with electricityTected by a circuit breaker Preventing Electrostatic Discharge Damage General observations Typographical conventions used in this document General conventionsChapter contents General informationModel 2160 overview ModelModel 2160 front panel LED descriptionsWAN 1-4 Link LAN 1-4100MModel 2160 rear panel Port descriptionsReset button Ground terminalApplications overview Introduction Typical applicationDistance charts Distance Chart 2160 Series Standard SettingDistance Chart 2160 Series High Speed Setting Hardware installation Planning the installation IP related information Network diagramAC Power Mains Installing the Model Connecting cablesLocation and mounting requirements Unpacking the ModelGrounding the Model 2160 and connecting power Grounding studConﬁguring the Model Web conﬁguration requirementsConsole conﬁguration requirements Telnet conﬁguration requirementsWeb conﬁguration Web configuration System Login Setting Up the WMITCP/IP setup Operation mode and Mgmt port Basic Conﬁguration OptionsSubnet Mask Host Name Soho Dhcp serverLAN IP Address Subnet Mask Gateway DNS Server 1 DNS Server 2 Review and save basic setup changes Review and save basic setup changesAnnex Type Advanced Conﬁguration OptionsLine Type Tcpam Type Main RateSNR Margin Line ProbeVlan VID 802.1Q Tag-Based Vlan 1Q Tag-Based Vlan802.1Q Vlan Web configuration Port-Based Vlan Port-Based VlanPort-Based QinQ Tpid Tag Protocol Identiﬁer Enter 33024 for IEEE802.1QQuality of Service QoS Port Based Priority QoS Port Based PriorityVlan Tag Priority QoS Vlan Tag PriorityDefault Service by WRR IP Dscp PriorityDelay Normal Stays the same link layer and routing protocol keep aliveClass Throughput Normal High ReliabilityQoS IP Dscp Priority Rate Control Rate ControlMgmt Status Status OptionsLine Status LAN Status Administration OptionsSecurity Administration User Proﬁles Remote Management HostsSnmp Administration Snmp AdministrationCommunity Pool Snmp community pool conﬁgurationSystem Information Utility OptionsTrap Host Pool Conﬁguration Tool Conﬁguration ToolUpgrade LogoutRestart RestartConsole and Telnet conﬁguration Dhcp Server Dhcp Fixed Host DNS Proxy Host NameConsole and Telnet configuration Log in using Telnet Interface commandsCtrl + C Quit conﬁguring the item Ctrl +Q Access help Log in to the console interfaceWindow structure Product name Line BridgeMain Menu Tree Menu tree for authorized usersMenu tree for unauthorized users Main screen for authorized usersEnable Command Menu Setup Command Menu LineWire model ModeLink Maximum Main RateClear IP Address Subnet MaskVlan Mode Disable 802.1Q Tag Vlan Port-Based VlanSetup Command Menu Pvid QoS Mode QoSQueue Schedule Queue WeightQoS Mode Weight Value Port-Based Priority QoS Vlan Tag Priority QoSIP Dscp Priority QoS Vlan Tag Index 0 1 2 3 4 5 6 Queue IndexList RatePort Port LineMgmt Dhcp Server Dhcp Fixed HostHost Name Factory DefaultDNS Proxy Interface Status Command MenuInterface Status Show Command Menu Write CommandSystem ConﬁgReboot Command Ping CommandModify/Add User Administration Command MenuUser Proﬁle Legal IP Address Pool SecurityTelnet TCP Port Snmp CommunityTrap host ReadOnlyReadWrite DeniedSupervisor ID Supervisor Password and IDSupervisor Password Utility Command Menu Upgrade main softwareBackup system conﬁguration Restore system conﬁgurationExit Command Contacting Patton for assistance Warranty coverage Contact informationOut-of-warranty service Returns for creditReturn for credit policy RMA numbersAppendix a Compliance information Compliance Radio and TV interference FCC PartCE Declaration of Conformity Authorized European RepresentativeAppendix B Speciﬁcations Line Connector Ethernet ConnectorManagement Connector Line ModulationFront Panel Indicators Power SupplyDimensions WeightAppendix C Port pin-outs Console port EIA-561 RJ-45 8-pin portEthernet Line CopperLink