Patton electronic 4630 Series manual IP services, Management, System, Physical

Page 46

SmartNode 4630 Getting Started Guide	B • Specifications

IP services

IPv4 router; RIPv1, v2 (RFC 1058 and 2453)

Programmable static routes

ICMP redirect (RFC 792); Packet fragmentation

DiffServe/ToS set or queue per header bits

Pocket Policing discards excess trafﬁc

802.1p VLAN tagging IPSEC AH & ESP Modes Manual Key; IKE optional AES/DES/3DES Encryption

Note To use the IPSec VPN capabilities including AES/DES/3DES encryption with the SmartNode 4630, you may need to purchase additional license keys.

Management

Web-based GUI

Industry standard CLI with local console (RJ-45. RJ-232, 9600 bps, 8, N, 1) and remote Telnet access, fully documented

HTTP web management and ﬁrmware loading

TFTP conﬁguration & ﬁrmware loading

SNMP v1 agent (MIB II and private MIB)

Built-in diagnostic tools (trace, debug)

Secure Auto-provisioning

System

CPU Motorola MC875 operating at 66 MHz

Memory:

•32 Mbytes SDRAM

•8 Mbytes Flash

Physical

Dimensions: 11W x 1.5H x 6.2D inch (280W x 39H x 157D mm)

Weight: <21 oz. (<600g)

Power Consumption: < 10W

Operating temperature: 32–104°F(0–40°C)

IP services

46

Image 46

Contents SmartNode 4630 Series Mailsupport@patton.com Summary Table of Contents Table of Contents Contacting Patton for assistance Cabling List of Figures List of Tables Audience About this guideStructure Precautions Safety when working with electricityGeneral observations Typographical conventions used in this documentGeneral conventions Node Chapter contents General informationSmartNode 4630 overview SmartNodeSmartNode 4630 rear panel BRI 0/0BRI 0/2 60 Hz ResetBRI 0/1 BRI 0/3SmartNode 4630 front panel PowerRun Ethernet Link VoIP LinkBRI Link/Sig Ethernet 100MApplications overview Introduction Application-Edge intelligence of enterprise communicationApplication-Multi-service Isdn Internet telephony IAD How it worksApplications overview SmartNode installation Site log Planning the installationNetwork Diagram Network informationInstalling the gateway router Connecting the 10/100Base-T Ethernet LAN and WAN cables Connecting the power supply Initial conﬁguration Connecting the SmartNode to your laptop PC Connecting the SmartNode to your laptop PCConﬁguring the desired IP address Factory-default IP settingsLogin Changing the WAN IP addressConnecting the SmartNode to the network Connecting the SmartNode to the networkLoading the conﬁguration optional Start-up with factory conﬁguration BootloaderStart Bootloader Load a new application image SmartWare via TftpOptional RedBoot load -r -v -h host -b Load a new application image SmartWare via the serial link RedBoot load -r -v -mXmodem ymodem -b Additional information Contacting Patton for assistance Contact information Warranty coveragePatton support headquarters in the USA Out-of-warranty service RMA numbersAppendix a Compliance information Radio and TV Interference SafetyCompliance CE Declaration of ConformityIsdn compliance Appendix B Speciﬁcations Voice connectivity Voice processing signalling dependentData connectivity Fax and modem support Voice signallingVoice routing-session router System IP servicesManagement PhysicalIdentiﬁcation of the SmartNode devices via Snmp SmartNode Model SysObjectIDAppendix C Cabling Connecting a serial terminal ConsoleTypical Ethernet straight-through cable diagram EthernetIsdn BRI Appendix D Port pin-outs Console port Isdn BRI 0/0 NT/Net or TE/User portIsdn BRI 0/1 . /3 TE/Usr or NT/Net Appendix E SmartNode 4630 factory conﬁguration Introduction Appendix F End user license agreement End User License Agreement Termination Other licenses