Patton electronic 4630 Series manual Termination, Other licenses

Page 59

SmartNode 4630 Getting Started Guide

F • End user license agreement

 

 

If the Program(s) are acquired by or on behalf of a unit or agency of the United States Government, the Gov- ernment agrees that such Program(s) are commercial computer software or computer software documentation and that, absent a written agreement to the contrary, the Government’s rights with respect to such Program(s) are limited by the terms of this Agreement, pursuant to Federal Acquisition Regulations 12.212(a) and/or DEARS 227.7202-1(a) and/or sub-paragraphs (a) through (d) of the “Commercial Computer Software - Restricted Rights” clause at 48 C.F.R. 52.227-19 of the Federal Acquisition Regulations as applicable.

6. Termination

A)The End User may terminate this agreement by returning the Designated Equipment and destroying all copies of the licensed Program(s).

B)Patton Electronics Company may terminate this Agreement should End User violate any of the provi- sions of section “4. Grant of License” on page 58.

C)Upon termination for A or B above or the end of the Term, End User is required to destroy all copies of the licensed Program(s)

7. Other licenses

The Program may be subject to licenses extended by third parties. Accordingly, Patton Electronics Company licenses the Programs subject to the terms and conditions dictated by third parties. Third party software identi- fied to the Programs includes:

A routing license is included at no charge.

MGCP and VPN capabilities will require the purchase of an additional license.

The LGPL (Lesser General Public License) open source license distributed to you pursuant to the LGPL license terms (http://www.gnu.org/licenses/lgpl.html).

RedBoot (Red Hat Embedded Debug and Bootstrap) embedded system debug/bootstrap environment from Red Hat distributed to you pursuant to the eCos license terms (http://ecos.sourceware.org/license- overview.html) and GNU General Public License (GPL) terms (http://www.gnu.org/copyleft/gpl.html). Source code is available upon request.

End User License Agreement

59

Image 59
Contents SmartNode 4630 Series Mailsupport@patton.com Summary Table of Contents Table of Contents Contacting Patton for assistance Cabling List of Figures List of Tables Structure About this guideAudience Safety when working with electricity PrecautionsGeneral conventions Typographical conventions used in this documentGeneral observations Node General information Chapter contentsSmartNode SmartNode 4630 overviewBRI 0/0 SmartNode 4630 rear panelBRI 0/3 60 Hz ResetBRI 0/1 BRI 0/2Run PowerSmartNode 4630 front panel Ethernet 100M VoIP LinkBRI Link/Sig Ethernet LinkApplications overview Application-Edge intelligence of enterprise communication IntroductionHow it works Application-Multi-service Isdn Internet telephony IADApplications overview SmartNode installation Network information Planning the installationNetwork Diagram Site logInstalling the gateway router Connecting the 10/100Base-T Ethernet LAN and WAN cables Connecting the power supply Initial configuration Connecting the SmartNode to your laptop PC Connecting the SmartNode to your laptop PCChanging the WAN IP address Factory-default IP settingsLogin Configuring the desired IP addressConnecting the SmartNode to the network Connecting the SmartNode to the networkLoading the configuration optional Load a new application image SmartWare via Tftp BootloaderStart Bootloader Start-up with factory configurationOptional RedBoot load -r -v -h host -b Xmodem ymodem -b RedBoot load -r -v -mLoad a new application image SmartWare via the serial link Additional information Contacting Patton for assistance Patton support headquarters in the USA Warranty coverageContact information RMA numbers Out-of-warranty serviceAppendix a Compliance information CE Declaration of Conformity SafetyCompliance Radio and TV InterferenceIsdn compliance Appendix B Specifications Data connectivity Voice processing signalling dependentVoice connectivity Voice routing-session router Voice signallingFax and modem support Physical IP servicesManagement SystemSmartNode Model SysObjectID Identification of the SmartNode devices via SnmpAppendix C Cabling Console Connecting a serial terminalEthernet Typical Ethernet straight-through cable diagramIsdn BRI Appendix D Port pin-outs Isdn BRI 0/0 NT/Net or TE/User port Console portIsdn BRI 0/1 . /3 TE/Usr or NT/Net Appendix E SmartNode 4630 factory configuration Introduction Appendix F End user license agreement End User License Agreement Other licenses Termination