TP-Link TL-WN322G manual Installation Guide, Before You Begin, Installing the Drivers

Page 10

Chapter 2 Installation Guide

TL-WN322G54M Wireless USB Adapter User Guide

Chapter 2 Installation Guide

2.1 Before You Begin

Before installing the new drivers of your TL-WN322G 54M Wireless USB Adapter, you need to disable all of the Wireless LAN drivers that you have installed.

During the installation, Windows 98/ME/2000/XP/2003/64bit XP may need to copy systems files from its installation CD. Therefore, you may need a copy of the Windows installation CD at hand before installing the drivers.

2.2 Installing the Drivers

Follow the steps below in order to install the TL-WN322G 54M Wireless USB Adapter drivers:

¾Insert the Resource CD into your CD-ROM drive, Click the Start button and choose Run. In the field that appears, enter F:\XXX\Setup.exe(if "F" is the letter of your CD-ROM drive; XXX represents the setup program path, which is labeled on the Resource CD).

¾Once the setup begins you will see the Install Shield Wizard, as the image depicts below.

Figure 2-1 Install driver wizard

¾Click on the Next button to continue.

¾Select the location where you would like the driver installed. Click on the Browse button to change the directory, or click on the Next button to continue using the default directory.

- 5 -

Image 10

Contents Page COPYRIGHT & TRADEMARKS All rights reservedIMPORTANT NOTE FCC Radiation Exposure Statement FCC STATEMENTFCC RF Radiation Exposure Statement CE Declaration of Conformity¾ EN 300 328 V.1.4.1 ¾ EN 301 489-1 V.1.4.1 2002 / EN 301 489-17 V.1.2.1 ¾ EN 60950-1Chapter TL-WN322G 54M Wireless USB Adapter User Guide Package Contentsy Drivers and Utility Chapter 1 Introduction 1.1 FeaturesLED Indicator 1.2 LED StatusAd-hoc peer-to-peer Mode 1.4 Network ConfigurationInfrastructure Mode Figure 1-2 Infrastructure mode 2.2 Installing the Drivers Chapter 2 Installation Guide2.1 Before You Begin Figure 2-3 Install Shield-Setup Status Figure 2-2 Install Shield-Choose Destination Location¾ Wait a few moments until the files are copied to the computer Figure 2-4 Installation Complete 1. Click on Start Settings Control Panel Add or Remove Programs Chapter 3 Uninstall Guide3.1 Through Control Panel TL-WN322G Wireless Utility 3.2 Through ProgramsFigure 3-5 Confirm the Uninstalling process Figure 3-6 Uninstalling TL-WN322G Wireless Utility and the driversFigure 3-7 Uninstalling process finished 4.1.1.1 General Connection Setting Chapter 4 Software Configuration4.1 Station Mode Configuration ¾ Current Network InformationFigure 4-2 More setting ¾ You can click “Change” button to change general connection settingsFigure 4-3 More setting-Click Change Figure 4-4 More setting-WEP 4.1.1.2 WEP Encryption 4.1.1.3 WPA/WPA2 Authentication with TKIP/AES Encryption ¾ Click on the WPA Encryption Setting button Figure 4-8 WPA setting ¾ Protocol Select TLS from the drop-down list 4.1.1.4 WPA-PSK Authentication 4.1.1.5 Profiles4.1.1.6 Advanced Settings 4.2 Wireless network mode configuration Figure 4-15 Access point setting 5.1 Configuration of WEP Encryption Chapter 5 Examples for applicationStep 6 ： Step 3：ClickStep Part 1：Configuration of our TL-WN322G 54M Wireless USB Adapter 5.2 Configuration of PSP ModeThere is two parts of this setting： Step One： Select “Access Point” from the drop down listRemark Step Six：Select address settings mode-Easy Step Nine： ”Proxy Server” select ”Do Not Use” Step Ten： Select ”Test Connection”Appendix A Glossary ¾ PSK- Pre-Shared Key ¾ TKIP- Temporal Key Integrity Protocol ¾ PEAP- Protected Extended Authentication Protocol¾ RADIUS- Remote Authentication Dial In User Service ¾ AES- Advanced Encryption Standard ¾ TLS- Transport Layer SecurityTransmit Power Appendix B SpecificationsMedia Access Safety& EmissionsAppendix C Contact Information