TP-Link manual TL-WN322G 54M Wireless USB Adapter User Guide, 4 More setting-WEP

Page 20

Figure 4-4 More setting—WEP

TL-WN322G54M Wireless USB Adapter User Guide

Figure 4-4 More setting—WEP

¾SSID: Enter the SSID of the network. The SSID is a unique name shared among all points in your wireless network. The SSID must be identical for all points in the network, and is case-sensitive. Place a check in the any box if you would like the device to connect to the first available Access Point with the strongest signal.

¾Network Type: Select a network type from the drop-down list.

¾Infrastructure or Ad-hoc:If you select infrastructure, the device must be connected to an Access Point. If you select ad-hoc, you may connect the device to another WLAN client adapter (such as this one).

¾Authentication: Select an authentication type from the drop down list. Options

available are: Auto, Open System, Shared Key, WPA, WPA-PSK, WPA2, WPA2-PSK.

¾Encryption: Select an encryption type from the drop-down list. Options available are: Disable, WEP, TKIP, AES.

Note: Refer to the WEP encryption and WPA encryption sections in this chapter to configure the security settings.

- 15 -

Image 20

Contents Page COPYRIGHT & TRADEMARKS All rights reservedFCC STATEMENT FCC RF Radiation Exposure StatementIMPORTANT NOTE FCC Radiation Exposure Statement CE Declaration of Conformity¾ EN 300 328 V.1.4.1 ¾ EN 301 489-1 V.1.4.1 2002 / EN 301 489-17 V.1.2.1 ¾ EN 60950-1Chapter y Drivers and Utility Package ContentsTL-WN322G 54M Wireless USB Adapter User Guide 1.1 Features LED IndicatorChapter 1 Introduction 1.2 LED StatusInfrastructure Mode 1.4 Network ConfigurationAd-hoc peer-to-peer Mode Figure 1-2 Infrastructure mode 2.1 Before You Begin Chapter 2 Installation Guide2.2 Installing the Drivers ¾ Wait a few moments until the files are copied to the computer Figure 2-2 Install Shield-Choose Destination LocationFigure 2-3 Install Shield-Setup Status Figure 2-4 Installation Complete 3.1 Through Control Panel Chapter 3 Uninstall Guide1. Click on Start Settings Control Panel Add or Remove Programs TL-WN322G Wireless Utility 3.2 Through ProgramsFigure 3-5 Confirm the Uninstalling process Figure 3-6 Uninstalling TL-WN322G Wireless Utility and the driversFigure 3-7 Uninstalling process finished Chapter 4 Software Configuration 4.1 Station Mode Configuration4.1.1.1 General Connection Setting ¾ Current Network InformationFigure 4-2 More setting ¾ You can click “Change” button to change general connection settingsFigure 4-3 More setting-Click Change Figure 4-4 More setting-WEP 4.1.1.2 WEP Encryption 4.1.1.3 WPA/WPA2 Authentication with TKIP/AES Encryption ¾ Click on the WPA Encryption Setting button Figure 4-8 WPA setting ¾ Protocol Select TLS from the drop-down list 4.1.1.4 WPA-PSK Authentication 4.1.1.5 Profiles4.1.1.6 Advanced Settings 4.2 Wireless network mode configuration Figure 4-15 Access point setting 5.1 Configuration of WEP Encryption Chapter 5 Examples for applicationStep Step 3：ClickStep 6 ： 5.2 Configuration of PSP Mode There is two parts of this setting：Part 1：Configuration of our TL-WN322G 54M Wireless USB Adapter Step One： Select “Access Point” from the drop down listRemark Step Six：Select address settings mode-Easy Step Nine： ”Proxy Server” select ”Do Not Use” Step Ten： Select ”Test Connection”Appendix A Glossary ¾ PEAP- Protected Extended Authentication Protocol ¾ RADIUS- Remote Authentication Dial In User Service¾ PSK- Pre-Shared Key ¾ TKIP- Temporal Key Integrity Protocol ¾ AES- Advanced Encryption Standard ¾ TLS- Transport Layer SecurityAppendix B Specifications Media AccessTransmit Power Safety& EmissionsAppendix C Contact Information