TP-Link TL-WN322G manual Chapter

Page 5

Package Contents			..1
Chapter 1	Introduction		..2
1.1	Features		..2
1.2	LED Status		..2
1.3	System Requirements		..2
1.4	Network Configuration		..3
Chapter 2	Installation Guide		..5
2.1	Before You Begin		5
2.2	Installing the Drivers		..5
Chapter 3	Uninstall Guide		8
3.1	Through Control Panel		..8
3.2	Through Programs		..9
Chapter 4	Software Configuration		12
4.1	Station Mode Configuration		12
4.1.1 More Setting			12
	4.1.1.1	General Connection Setting	12
	4.1.1.2	WEP Encryption	16
	4.1.1.3	WPA/WPA2 Authentication with TKIP/AES Encryption	17
	4.1.1.4	WPA-PSK Authentication	20
	4.1.1.5	Profiles	20
	4.1.1.6	Advanced Settings	21
4.2	Wireless network mode configuration		22
Chapter 5	Examples for application		24
5.1	Configuration of WEP Encryption		24
5.2	Configuration of PSP Mode		26
Appendix A: Glossary			30
Appendix B: Specifications			32
Appendix C: Contact Information			33

Image 5

Contents Page All rights reserved COPYRIGHT & TRADEMARKSFCC RF Radiation Exposure Statement FCC STATEMENTIMPORTANT NOTE FCC Radiation Exposure Statement CE Declaration of Conformity¾ EN 301 489-1 V.1.4.1 2002 / EN 301 489-17 V.1.2.1 ¾ EN 60950-1 ¾ EN 300 328 V.1.4.1Chapter y Drivers and Utility Package ContentsTL-WN322G 54M Wireless USB Adapter User Guide LED Indicator 1.1 FeaturesChapter 1 Introduction 1.2 LED StatusInfrastructure Mode 1.4 Network ConfigurationAd-hoc peer-to-peer Mode Figure 1-2 Infrastructure mode 2.1 Before You Begin Chapter 2 Installation Guide2.2 Installing the Drivers ¾ Wait a few moments until the files are copied to the computer Figure 2-2 Install Shield-Choose Destination LocationFigure 2-3 Install Shield-Setup Status Figure 2-4 Installation Complete 3.1 Through Control Panel Chapter 3 Uninstall Guide1. Click on Start Settings Control Panel Add or Remove Programs 3.2 Through Programs TL-WN322G Wireless UtilityFigure 3-6 Uninstalling TL-WN322G Wireless Utility and the drivers Figure 3-5 Confirm the Uninstalling processFigure 3-7 Uninstalling process finished 4.1 Station Mode Configuration Chapter 4 Software Configuration4.1.1.1 General Connection Setting ¾ Current Network Information¾ You can click “Change” button to change general connection settings Figure 4-2 More settingFigure 4-3 More setting-Click Change Figure 4-4 More setting-WEP 4.1.1.2 WEP Encryption 4.1.1.3 WPA/WPA2 Authentication with TKIP/AES Encryption ¾ Click on the WPA Encryption Setting button Figure 4-8 WPA setting ¾ Protocol Select TLS from the drop-down list 4.1.1.5 Profiles 4.1.1.4 WPA-PSK Authentication4.1.1.6 Advanced Settings 4.2 Wireless network mode configuration Figure 4-15 Access point setting Chapter 5 Examples for application 5.1 Configuration of WEP EncryptionStep Step 3：ClickStep 6 ： There is two parts of this setting： 5.2 Configuration of PSP ModePart 1：Configuration of our TL-WN322G 54M Wireless USB Adapter Step One： Select “Access Point” from the drop down listRemark Step Six：Select address settings mode-Easy Step Ten： Select ”Test Connection” Step Nine： ”Proxy Server” select ”Do Not Use”Appendix A Glossary ¾ RADIUS- Remote Authentication Dial In User Service ¾ PEAP- Protected Extended Authentication Protocol¾ PSK- Pre-Shared Key ¾ TKIP- Temporal Key Integrity Protocol ¾ AES- Advanced Encryption Standard ¾ TLS- Transport Layer SecurityMedia Access Appendix B SpecificationsTransmit Power Safety& EmissionsAppendix C Contact Information