TP-Link manual Advanced Settings, TL-WN322G 54M Wireless USB Adapter User Guide

Page 26

4.1.1.6 Advanced Settings

TL-WN322G54M Wireless USB Adapter User Guide

Figure 4-10 More Setting—Profile

¾Profile Name: Displays the name of current profile. One device can have many profiles, but only one profile can be loaded at a time.

¾Load: Select a profile from the drop-down list and then click on the Load button.

¾Save Current: Enter a new profile name and then click on the Save Current button to save the profile.

¾Delete: To delete an existing profile, select it from the drop-down list and then click on the Delete button.

4.1.1.6 Advanced Settings

The Advanced Settings allows you to configure the user interface language, power consumption, and threshold values.

- 21 -

Image 26

Contents Page COPYRIGHT & TRADEMARKS All rights reservedIMPORTANT NOTE FCC Radiation Exposure Statement FCC STATEMENTFCC RF Radiation Exposure Statement CE Declaration of Conformity¾ EN 300 328 V.1.4.1 ¾ EN 301 489-1 V.1.4.1 2002 / EN 301 489-17 V.1.2.1 ¾ EN 60950-1Chapter y Drivers and Utility Package ContentsTL-WN322G 54M Wireless USB Adapter User Guide Chapter 1 Introduction 1.1 FeaturesLED Indicator 1.2 LED StatusInfrastructure Mode 1.4 Network ConfigurationAd-hoc peer-to-peer Mode Figure 1-2 Infrastructure mode 2.1 Before You Begin Chapter 2 Installation Guide2.2 Installing the Drivers ¾ Wait a few moments until the files are copied to the computer Figure 2-2 Install Shield-Choose Destination LocationFigure 2-3 Install Shield-Setup Status Figure 2-4 Installation Complete 3.1 Through Control Panel Chapter 3 Uninstall Guide1. Click on Start Settings Control Panel Add or Remove Programs TL-WN322G Wireless Utility 3.2 Through ProgramsFigure 3-5 Confirm the Uninstalling process Figure 3-6 Uninstalling TL-WN322G Wireless Utility and the driversFigure 3-7 Uninstalling process finished 4.1.1.1 General Connection Setting Chapter 4 Software Configuration4.1 Station Mode Configuration ¾ Current Network InformationFigure 4-2 More setting ¾ You can click “Change” button to change general connection settingsFigure 4-3 More setting-Click Change Figure 4-4 More setting-WEP 4.1.1.2 WEP Encryption 4.1.1.3 WPA/WPA2 Authentication with TKIP/AES Encryption ¾ Click on the WPA Encryption Setting button Figure 4-8 WPA setting ¾ Protocol Select TLS from the drop-down list 4.1.1.4 WPA-PSK Authentication 4.1.1.5 Profiles4.1.1.6 Advanced Settings 4.2 Wireless network mode configuration Figure 4-15 Access point setting 5.1 Configuration of WEP Encryption Chapter 5 Examples for applicationStep Step 3：ClickStep 6 ： Part 1：Configuration of our TL-WN322G 54M Wireless USB Adapter 5.2 Configuration of PSP ModeThere is two parts of this setting： Step One： Select “Access Point” from the drop down listRemark Step Six：Select address settings mode-Easy Step Nine： ”Proxy Server” select ”Do Not Use” Step Ten： Select ”Test Connection”Appendix A Glossary ¾ PSK- Pre-Shared Key ¾ TKIP- Temporal Key Integrity Protocol ¾ PEAP- Protected Extended Authentication Protocol¾ RADIUS- Remote Authentication Dial In User Service ¾ AES- Advanced Encryption Standard ¾ TLS- Transport Layer SecurityTransmit Power Appendix B SpecificationsMedia Access Safety& EmissionsAppendix C Contact Information