TP-Link TL-WN322G manual ¾ EN 300 328 V.1.4.1

Page 4

Is here with confirmed to comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility (89/336/EEC), Low-voltage Directive (73/23/EEC) and the Amendment Directive (93/68/EEC), the procedures given in European Council Directive 99/5/EC and 89/3360EEC.

The equipment was passed. The test was performed according to the following European standards:

¾EN 300 328 V.1.4.1 (2003)

¾EN 301 489-1 V.1.4.1 (2002) / EN 301 489-17 V.1.2.1 (2002)

¾EN 60950-1: 2001

European standards dictate maximum radiated transmit power of 100mW EIRP and frequency range 2.400-2.4835GHz; In France, the equipment must be restricted to the 2.4465-2.4835GHz frequency range and must be restricted to indoor use.

Image 4

Contents Page COPYRIGHT & TRADEMARKS All rights reservedFCC STATEMENT FCC RF Radiation Exposure StatementIMPORTANT NOTE FCC Radiation Exposure Statement CE Declaration of Conformity¾ EN 300 328 V.1.4.1 ¾ EN 301 489-1 V.1.4.1 2002 / EN 301 489-17 V.1.2.1 ¾ EN 60950-1Chapter TL-WN322G 54M Wireless USB Adapter User Guide Package Contentsy Drivers and Utility 1.1 Features LED IndicatorChapter 1 Introduction 1.2 LED StatusAd-hoc peer-to-peer Mode 1.4 Network ConfigurationInfrastructure Mode Figure 1-2 Infrastructure mode 2.2 Installing the Drivers Chapter 2 Installation Guide2.1 Before You Begin Figure 2-3 Install Shield-Setup Status Figure 2-2 Install Shield-Choose Destination Location¾ Wait a few moments until the files are copied to the computer Figure 2-4 Installation Complete 1. Click on Start Settings Control Panel Add or Remove Programs Chapter 3 Uninstall Guide3.1 Through Control Panel TL-WN322G Wireless Utility 3.2 Through ProgramsFigure 3-5 Confirm the Uninstalling process Figure 3-6 Uninstalling TL-WN322G Wireless Utility and the driversFigure 3-7 Uninstalling process finished Chapter 4 Software Configuration 4.1 Station Mode Configuration4.1.1.1 General Connection Setting ¾ Current Network InformationFigure 4-2 More setting ¾ You can click “Change” button to change general connection settingsFigure 4-3 More setting-Click Change Figure 4-4 More setting-WEP 4.1.1.2 WEP Encryption 4.1.1.3 WPA/WPA2 Authentication with TKIP/AES Encryption ¾ Click on the WPA Encryption Setting button Figure 4-8 WPA setting ¾ Protocol Select TLS from the drop-down list 4.1.1.4 WPA-PSK Authentication 4.1.1.5 Profiles4.1.1.6 Advanced Settings 4.2 Wireless network mode configuration Figure 4-15 Access point setting 5.1 Configuration of WEP Encryption Chapter 5 Examples for applicationStep 6 ： Step 3：ClickStep 5.2 Configuration of PSP Mode There is two parts of this setting：Part 1：Configuration of our TL-WN322G 54M Wireless USB Adapter Step One： Select “Access Point” from the drop down listRemark Step Six：Select address settings mode-Easy Step Nine： ”Proxy Server” select ”Do Not Use” Step Ten： Select ”Test Connection”Appendix A Glossary ¾ PEAP- Protected Extended Authentication Protocol ¾ RADIUS- Remote Authentication Dial In User Service¾ PSK- Pre-Shared Key ¾ TKIP- Temporal Key Integrity Protocol ¾ AES- Advanced Encryption Standard ¾ TLS- Transport Layer SecurityAppendix B Specifications Media AccessTransmit Power Safety& EmissionsAppendix C Contact Information