TP-Link TL-WN322G manual Uninstall Guide, Through Control Panel

Page 13

Chapter 3 Uninstall Guide

TL-WN322G54M Wireless USB Adapter User Guide

Chapter 3 Uninstall Guide

If the device installation is unsuccessful for any reason, the best way to solve the problem may be to completely uninstall the device and its utility and repeat the installation procedure again. Hereby, customers can use one of the following two methods to uninstall the Drivers and Utility.

3.1 Through Control Panel

Follow the steps below in order to uninstall the Drivers and Utility:

1.Click on Start > Settings > Control Panel > Add or Remove Programs

2.You will then see the following window. Select the TL-WN322G Wireless Utility and then click on Remove.

Figure 3-1 Add or Remove Programs

3. Click on the OK button to confirm the Uninstalling process.

Figure 3-2 Confirm the Uninstalling process.

4.The process will then remove TL-WN322G Wireless Utility and the drivers from your computer. Click on the Finish button and then remove the TL-WN322G 54M Wireless

-8 -

Image 13

Contents Page All rights reserved COPYRIGHT & TRADEMARKSFCC RF Radiation Exposure Statement FCC STATEMENTIMPORTANT NOTE FCC Radiation Exposure Statement CE Declaration of Conformity¾ EN 301 489-1 V.1.4.1 2002 / EN 301 489-17 V.1.2.1 ¾ EN 60950-1 ¾ EN 300 328 V.1.4.1Chapter TL-WN322G 54M Wireless USB Adapter User Guide Package Contentsy Drivers and Utility LED Indicator 1.1 FeaturesChapter 1 Introduction 1.2 LED StatusAd-hoc peer-to-peer Mode 1.4 Network ConfigurationInfrastructure Mode Figure 1-2 Infrastructure mode 2.2 Installing the Drivers Chapter 2 Installation Guide2.1 Before You Begin Figure 2-3 Install Shield-Setup Status Figure 2-2 Install Shield-Choose Destination Location¾ Wait a few moments until the files are copied to the computer Figure 2-4 Installation Complete 1. Click on Start Settings Control Panel Add or Remove Programs Chapter 3 Uninstall Guide3.1 Through Control Panel 3.2 Through Programs TL-WN322G Wireless UtilityFigure 3-6 Uninstalling TL-WN322G Wireless Utility and the drivers Figure 3-5 Confirm the Uninstalling processFigure 3-7 Uninstalling process finished 4.1 Station Mode Configuration Chapter 4 Software Configuration4.1.1.1 General Connection Setting ¾ Current Network Information¾ You can click “Change” button to change general connection settings Figure 4-2 More settingFigure 4-3 More setting-Click Change Figure 4-4 More setting-WEP 4.1.1.2 WEP Encryption 4.1.1.3 WPA/WPA2 Authentication with TKIP/AES Encryption ¾ Click on the WPA Encryption Setting button Figure 4-8 WPA setting ¾ Protocol Select TLS from the drop-down list 4.1.1.5 Profiles 4.1.1.4 WPA-PSK Authentication4.1.1.6 Advanced Settings 4.2 Wireless network mode configuration Figure 4-15 Access point setting Chapter 5 Examples for application 5.1 Configuration of WEP EncryptionStep 6 ： Step 3：ClickStep There is two parts of this setting： 5.2 Configuration of PSP ModePart 1：Configuration of our TL-WN322G 54M Wireless USB Adapter Step One： Select “Access Point” from the drop down listRemark Step Six：Select address settings mode-Easy Step Ten： Select ”Test Connection” Step Nine： ”Proxy Server” select ”Do Not Use”Appendix A Glossary ¾ RADIUS- Remote Authentication Dial In User Service ¾ PEAP- Protected Extended Authentication Protocol¾ PSK- Pre-Shared Key ¾ TKIP- Temporal Key Integrity Protocol ¾ AES- Advanced Encryption Standard ¾ TLS- Transport Layer SecurityMedia Access Appendix B SpecificationsTransmit Power Safety& EmissionsAppendix C Contact Information