TP-Link manual Through Programs, TL-WN322G Wireless Utility

Page 14

3.2 Through Programs

TL-WN322G54M Wireless USB Adapter User Guide

USB Adapter.

Figure 3-3 Uninstalling process finished

3.2 Through Programs

Follow the steps below in order to uninstall the Drivers and Utility:

¾Click on Start > programs > TP-LINK> TL-WN322G Wireless Utility> Uninstall

TL-WN322G Wireless Utility.

Figure 3-4 Uninstall from programs

¾Then, process will go to Install Shield Wizard. The screen will pop up the following conversation “Do you want to completely remove the selected application and all of its features”

¾Click on the OK button to confirm the Uninstalling process.

- 9 -

Image 14

Contents Page COPYRIGHT & TRADEMARKS All rights reservedIMPORTANT NOTE FCC Radiation Exposure Statement FCC STATEMENTFCC RF Radiation Exposure Statement CE Declaration of Conformity¾ EN 300 328 V.1.4.1 ¾ EN 301 489-1 V.1.4.1 2002 / EN 301 489-17 V.1.2.1 ¾ EN 60950-1Chapter y Drivers and Utility Package ContentsTL-WN322G 54M Wireless USB Adapter User Guide Chapter 1 Introduction 1.1 FeaturesLED Indicator 1.2 LED StatusInfrastructure Mode 1.4 Network ConfigurationAd-hoc peer-to-peer Mode Figure 1-2 Infrastructure mode 2.1 Before You Begin Chapter 2 Installation Guide2.2 Installing the Drivers ¾ Wait a few moments until the files are copied to the computer Figure 2-2 Install Shield-Choose Destination LocationFigure 2-3 Install Shield-Setup Status Figure 2-4 Installation Complete 3.1 Through Control Panel Chapter 3 Uninstall Guide1. Click on Start Settings Control Panel Add or Remove Programs TL-WN322G Wireless Utility 3.2 Through ProgramsFigure 3-5 Confirm the Uninstalling process Figure 3-6 Uninstalling TL-WN322G Wireless Utility and the driversFigure 3-7 Uninstalling process finished 4.1.1.1 General Connection Setting Chapter 4 Software Configuration4.1 Station Mode Configuration ¾ Current Network InformationFigure 4-2 More setting ¾ You can click “Change” button to change general connection settingsFigure 4-3 More setting-Click Change Figure 4-4 More setting-WEP 4.1.1.2 WEP Encryption 4.1.1.3 WPA/WPA2 Authentication with TKIP/AES Encryption ¾ Click on the WPA Encryption Setting button Figure 4-8 WPA setting ¾ Protocol Select TLS from the drop-down list 4.1.1.4 WPA-PSK Authentication 4.1.1.5 Profiles4.1.1.6 Advanced Settings 4.2 Wireless network mode configuration Figure 4-15 Access point setting 5.1 Configuration of WEP Encryption Chapter 5 Examples for applicationStep Step 3：ClickStep 6 ： Part 1：Configuration of our TL-WN322G 54M Wireless USB Adapter 5.2 Configuration of PSP ModeThere is two parts of this setting： Step One： Select “Access Point” from the drop down listRemark Step Six：Select address settings mode-Easy Step Nine： ”Proxy Server” select ”Do Not Use” Step Ten： Select ”Test Connection”Appendix A Glossary ¾ PSK- Pre-Shared Key ¾ TKIP- Temporal Key Integrity Protocol ¾ PEAP- Protected Extended Authentication Protocol¾ RADIUS- Remote Authentication Dial In User Service ¾ AES- Advanced Encryption Standard ¾ TLS- Transport Layer SecurityTransmit Power Appendix B SpecificationsMedia Access Safety& EmissionsAppendix C Contact Information