System Pre-Start Procedures

10.Measure the voltage again across Terminals R (-) and W (+). The measured voltage should now be approximately 0.2 VDC.

11.Turn the control circuit switch 1S2, in the unit control panel, to the “OFF” position.

12.Remove the wires from Terminals R, B, W, & Y.

13.Measure the resistance across the following pairs of terminals and compare the actual resistance readings with the values shown below:

(1)MEC Terminals R-to-W = 226 ohms

(2)MEC Terminals R-to-B = 432 ohms

(3)MEC Terminals R-to-Y = 226 ohms

14.Reconnect the economizer leads W, R, B and Y to the appropriate terminals on the controller.

15.Turn switches 1S2, 5S1, & 5S2 to the “ON” position to restore power to the control system.

Zone Thermostat Checkout (Honeywell T7067)

1.Open the system control switches 5S1 and 5S2 to disable the Evaporator Fan and Heating system.

2.Close the main power disconnect switch and turn the control circuit switch 1S2, in the unit control panel, “ON”.

WARNING

High Voltage is Present at Terminal Block 1TB1 or Unit Disconnect

Switch 1S1.

To prevent injury or death form electrocution, it is the responsibility of the technician to recognize this hazard and use extreme care when performing service procedures with the electrical power energized.

3.At the Zone Thermostat (6U37), use a digital voltmeter to verify that there is 20 volts DC power between thermostat Terminals 1 & 2. Refer to the illustration in Figure 31 for terminal identification. Refer to Table 12 for the thermostat “voltage output” ramps.

4.To check the “Cooling” output signal, place the voltmeter leads between thermostat Terminals 1 & 4. Refer to Figure 30 and;

a.move the cooling (blue) setpoint lever from right to left. As the cooling setpoint is lowered, the voltage signal should increase and the “Cooling” LED brighten.

b.move the cooling (blue) setpoint lever from left to right. As the cooling setpoint rises, the voltage signal should decrease and the “Cooling” LED dim.

5.To check the “Heating” output signal, place the voltmeter leads between thermostat Terminals 1 & 5. Refer to Figure 30 and;

a.move the heating (red) setpoint lever from left to right. As the heating setpoint rises, the voltage signal should increase and the “Heating” LED brighten.

b.move the heating (red) setpoint lever form right to left. As the heating setpoint lowers, the voltage signal should decrease and the “Heating” LED dim.

SS-SVX09A-EN

79

Page 78 Page 80
Page 79
Image 79
Trane RAUC-C30, RAUC-C50, RAUC-C60, RAUC-C20, RAUC-C40, RAUC-C25 manual Zone Thermostat Checkout Honeywell T7067
Page 78 Page 80

RAUC-C20, RAUC-C40, RAUC-C25, RAUC-C30, RAUC-C60 specifications

Trane, a leader in HVAC solutions, offers innovative air conditioning units designed for superior performance and energy efficiency. Among their advanced products are the Trane RAUC-C30, RAUC-C20, RAUC-C40, RAUC-C60, and RAUC-C50, which cater to various cooling and heating needs in residential and commercial applications.

The RAUC-C series showcases cutting-edge technology, ensuring effective climate control while minimizing energy consumption. These units are equipped with variable-speed compressors, allowing for precise cooling capacities and reduced noise levels during operation. This feature ensures that users can enjoy optimal comfort without the disruptive noise often associated with traditional HVAC systems.

One of the standout technologies used in the RAUC-C series is Trane’s advanced inverter technology. This system intelligently adjusts the compressor speed based on real-time cooling demands, enhancing efficiency and prolonging the unit's lifespan. Additionally, the units come with high SEER (Seasonal Energy Efficiency Ratio) ratings, making them an excellent choice for those looking to lower their energy bills while maintaining a comfortable indoor environment.

The RAUC-C series units are designed with durability in mind. Constructed with robust materials, these air conditioning systems are built to withstand varying weather conditions. Their compact and lightweight design makes installation straightforward, and they can fit seamlessly into a variety of spaces, from residential homes to commercial buildings.

Another key characteristic of the RAUC-C series is their eco-friendly refrigerant, which meets strict environmental regulations. This not only supports sustainability efforts but also ensures efficient cooling performance. Furthermore, their smart technology capabilities enable integration with modern smart home systems, allowing users to manage their cooling settings remotely for added convenience.

Trane's focus on user-friendly interfaces makes these units easy to operate. The intuitive control systems allow users to customize their cooling preferences easily, providing flexibility to adapt to individual comfort needs.

Overall, the Trane RAUC-C30, RAUC-C20, RAUC-C40, RAUC-C60, and RAUC-C50 stand out for their energy efficiency, advanced technology, durability, and user-focused design. These features make them reliable choices for anyone seeking efficient and effective heating and cooling solutions.
Top Page Image Contents