System Pre-Start Procedures

5.Install a jumper across the P and P1 terminals (remote setpoint input), and another jumper across terminals 6 and 7 (reset input) if reset is enabled.

6.Disconnect the wires from terminals T and T1 (discharge air sensor).

7.Remove the 3,400 ohm resistor (blue leads) from the test kit and connect it across terminals T and T1 to simulate a discharge air temperature of 60ºF.

8.Set the “Setpoint F” dial at 56ºF or below; then set the “Control Band F” dial at 2 to minimize the control response time.

9.At the Discharge Air controller, verify that the controller ground wire is connected to the chassis ground. Refer to the unit wiring diagram that shipped on the unit.

Note: It is not necessary to set the “Reset F” dial since the factory installed jumper across Terminals 6 and 7 disables this dial.

10.Turn the control circuit switch 1S2, in the unit control panel, and the main power disconnect switch for the condensing unit to the “ON” position.

WARNING

High Voltage is Present at Terminal Block 1TB1 or Unit Disconnect Switch 1S1.

To prevent injury or death form electrocution, it is the responsibility of the technician to recognize this hazard and use extreme care when performing service procedures with the electrical power energized.i

After approximately 2 minutes (time required to drive the economizer fully open), the LEDs on the W7100 should begin to illuminate as the cooling outputs stage “On”.

11.At the Discharge Air Controller, use a digital voltmeter to verify there is 24 volts AC across terminals TR & TR.

12.Set the “Setpoint F” dial at 64ºF; within 10 seconds, the LEDs should turn “Off” as the cooling outputs stage “Off”.

13.Immediately readjust the “Setpoint F” dial to 56oF; the LEDs should begin to illuminate again as the cooling outputs stage “On”.

If the unit includes the zone reset option, proceed to the next step; if not, proceed to step 18.

14.Set the “Reset F” dial at 15oF and the “Setpoint F” dial at 41ºF; then remove the jumper across terminals 6 & 7.

To simulate a call for maximum reset, install the 1780 ohm resistor (red leads), from the test kit, across terminals 6 and 7. The cooling LEDs should remain lit.

15.Turn the “Setpoint F” dial to 49ºF; within 1 to 2 minutes, the LEDs should turn “Off” as the cooling outputs stage “Off”.

16.As soon as all of the cooling LEDs are “Off”, remove the 1780 ohm resistor from terminals 6 and 7 and re-install the jumper across these terminals.

17.Adjust the “Setpoint F” dial to 56ºF; within 1 minute, the LEDs should illuminate as the cooling outputs stage “On”.

If the system includes an economizer, complete steps 18 through 23 to verify proper economizer control operation; if not, proceed to step 24.

18.With all of the cooling LEDs “On”, measure the DC voltage across terminals R (-) and W (+). The measured voltage should be 1.7 VDC to 2.1 VDC.

19.Set the “Setpoint F” dial at 64ºF to drive the economizer output to the minimum position. Within 2 minutes, the LEDs should turn “Off” as the cooling outputs stage “Off”.

72

SS-SVX09A-EN

Page 71 Page 73
Page 72
Image 72
Trane RAUC-C50, RAUC-C30, RAUC-C60, RAUC-C20, RAUC-C40, RAUC-C25 manual System Pre-Start Procedures
Page 71 Page 73

RAUC-C20, RAUC-C40, RAUC-C25, RAUC-C30, RAUC-C60 specifications

Trane, a leader in HVAC solutions, offers innovative air conditioning units designed for superior performance and energy efficiency. Among their advanced products are the Trane RAUC-C30, RAUC-C20, RAUC-C40, RAUC-C60, and RAUC-C50, which cater to various cooling and heating needs in residential and commercial applications.

The RAUC-C series showcases cutting-edge technology, ensuring effective climate control while minimizing energy consumption. These units are equipped with variable-speed compressors, allowing for precise cooling capacities and reduced noise levels during operation. This feature ensures that users can enjoy optimal comfort without the disruptive noise often associated with traditional HVAC systems.

One of the standout technologies used in the RAUC-C series is Trane’s advanced inverter technology. This system intelligently adjusts the compressor speed based on real-time cooling demands, enhancing efficiency and prolonging the unit's lifespan. Additionally, the units come with high SEER (Seasonal Energy Efficiency Ratio) ratings, making them an excellent choice for those looking to lower their energy bills while maintaining a comfortable indoor environment.

The RAUC-C series units are designed with durability in mind. Constructed with robust materials, these air conditioning systems are built to withstand varying weather conditions. Their compact and lightweight design makes installation straightforward, and they can fit seamlessly into a variety of spaces, from residential homes to commercial buildings.

Another key characteristic of the RAUC-C series is their eco-friendly refrigerant, which meets strict environmental regulations. This not only supports sustainability efforts but also ensures efficient cooling performance. Furthermore, their smart technology capabilities enable integration with modern smart home systems, allowing users to manage their cooling settings remotely for added convenience.

Trane's focus on user-friendly interfaces makes these units easy to operate. The intuitive control systems allow users to customize their cooling preferences easily, providing flexibility to adapt to individual comfort needs.

Overall, the Trane RAUC-C30, RAUC-C20, RAUC-C40, RAUC-C60, and RAUC-C50 stand out for their energy efficiency, advanced technology, durability, and user-focused design. These features make them reliable choices for anyone seeking efficient and effective heating and cooling solutions.
Top Page Image Contents