TP-Link td-w8961nd manual Installation Environment, Connecting the Router, Back to LED Explanation

Page 14

TD-W8961ND300Mbps Wireless N ADSL2+ Modem Router User Guide

2.3Installation Environment

¾The Product should not be located where it will be exposed to moisture or excessive heat.

¾Place the Router in a location where it can be connected to the various devices as well as to a power source.

¾Make sure the cables and power cord are safely placed out of the way so they do not create a tripping hazard.

¾The Router can be placed on a shelf or desktop.

¾Keep away from the strong electromagnetic radiation and the device of electromagnetic sensitive.

2.4Connecting the Router

Back to LED Explanation

Before installing the device, please make sure your broadband service provided by your ISP is available. If there is any problem, please contact your ISP. Before cable connection, cut off the power supply and keep your hands dry. You can follow the steps below to install it.

Step 1: Connect the ADSL Line.

Method one: Plug one end of the twisted-pair ADSL cable into the ADSL port on the rear panel of TD-W8961ND, and insert the other end into the wall socket.

Method two：You can use a separate splitter. External splitter can divide the data and voice, and then you can access the Internet and make calls at the same time. The external splitter has three ports:

•LINE: Connect to the wall jack

•PHONE: Connect to the phone sets

•MODEM: Connect to the ADSL port of TD-W8961ND

Plug one end of the twisted-pair ADSL cable into the ADSL port on the rear panel of TD-W8961ND. Connect the other end to the MODEM port of the external splitter.

Step 2: Connect the Ethernet cable. Attach one end of a network cable to your computer’s Ethernet port or a regular hub/switch port, and the other end to the LAN port on the TD-W8961ND.

Step 3: Power on the computers and LAN devices.

Step 4: Attach the power adapter. Connect the power adapter to the power connector on the rear of the device and plug in the adapter to a electrical outlet or power extension. The electrical outlet shall be installed near the device and shall be easily accessible.

7

Image 14

Contents TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router Rev 2.0.0COPYRIGHT & TRADEMARKS FCC RF Radiation Exposure Statement FCC STATEMENTCountry CE Mark WarningNational Restrictions RestrictionShenzhen, P. R. China DECLARATION OF CONFORMITYProduct Description 300Mbps Wireless N ADSL2+ Modem Router ETSI EN 300 328 V1.7.1Quick Installation Guide Package ContentsHardware Installation Software ConfigurationAppendix C Technical Support Appendix A SpecificationsAppendix B Troubleshooting MaintenanceTD-W8961ND Package Contents300Mbps Wireless N ADSL2+ Modem Router User Guide Chapter 1 Introduction 1.2 Main FeaturesWireless 1.1 Product Overview1.3 Conventions TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User GuideLED Explanation Chapter 2 Hardware Installation2.1 The Front Panel Name1. If the ADSL LED is off, please check your Internet connection first. Refer to 2.4 Connecting the Router for more information about how to make Internet connection correctly. If you have already made a right connection, please contact your ISP to make sure if your Internet service is available now 2.2 The Back Panel Back to LED Explanation 2.3 Installation Environment2.4 Connecting the Router TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Chapter 3 Quick Installation Guide 3.1 Configure PCTD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Step 4 Configure the IP address as Figure 3-4 shows. After that, click OK 1 Is the connection between your PC and the Router correct? 3.2 Login2 Is the TCP/IP configuration for your PC correct? Step 1 Select the Quick Start tab, then click RUN WIZARD, and you will see the next screen. Click the NEXT button and Connection Type. Then click NEXTStep 5 Configure the rules for the WLAN, and click NEXT Step 6 Click NEXT to finish the Quick Start4.1.1 Device Info Chapter 4 Software Configuration4.1 Status 4.1.2 System Log Click the SAVE LOG button to save the logs 4.1.3 StatisticsClick the CLEAR LOG button to clear the logs ¾ Select Ethernet, and you will see the statistics table as below Statistics Table¾ Select ADSL, and you will see the statistics table as below 4.2 Quick StartPlease refer to 3.2 Login ¾ Select WLAN, and you will see the statistics table as below4.3 Interface Setup 4.3.1 Internet1 Dynamic IP Address 2 Static IP Address 3 PPPoA/PPPoE 4.3.2 LAN 4 Bridge ModeTD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide IGMP Snoop Enable the IGMP Snoop function if you need How to assign a static IP address to the client? If you select Disabled, the DHCP function will not take effect4.3.3 Wireless TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide ¾ Multiple SSIDs Settings These are the settings of the SSID 1 WEP- 64Bits 2 WEP-128Bits 3 WPA-PSK4 WPA2-PSK 5 WPA-PSK/WPA2-PSKMethod One 4.3.3.1 WPS Settings1 PBC Method Two 2 PIN code 300Mbps Wireless N ADSL2+ Modem Router User Guide TD-W8961ND300Mbps Wireless N ADSL2+ Modem Router User Guide 4.4 Advanced Setup 4.4.1 Firewall4.4.2 Routing 4.4.3 NAT 4.4.3.1 DMZ 4.4.3.2 Virtual Server4.4.3.3 IP Address Mapping To add a virtual server entryOther operations for the entries as shown in Figure IP Address Mapping is only available for VCs with Multiple IPs 4.4.4 QoSTo add a mapping rule ¾ Summary Click the button to view the configurations of QoS 4.4.5 VLAN 1 Assign VLAN PVID for each Interface 2 Define VLAN Group4.4.6 ADSL 4.5 Access Management 4.5.1 ACL4.5.2 Filter 4.5.2.1 IP Filter¾ Interface Select the interface for the entry To add an IP Address filtering entry Step 5 Finally, click the SAVE to save the entry 4.5.2.2 MAC Filter To add a MAC Address filtering entrySelect the “MAC” as the Rule Type on the Filter screen show in Figure 4.5.2.3 Application Filter4.5.2.4 URL Filter To add a URL filter entry 4.5.3 SNMP 4.5.4 UPnP4.5.5 DDNS 4.5.6 CWMP4.6 Maintenance 1 NTP Server automatically 4.6.1 Administration4.6.2 Time Zone 2 PC’s Clock 3 Manually4.6.3 Firmware To upgrade the routers firmware, follow these instructions belowTo restore the Router’s settings 3 The router will reboot after the upgrading has been finishedTo back up the Router’s current settings 4.6.5 Diagnostics 4.6.4 SysRestart4.7 Help TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Physical and Environment Appendix A SpecificationsGeneral 3. What can I do if I cannot access the web-based configuration page? Appendix B Troubleshooting2. What can I do if I don’t know or forgot my password? For Windows XP OSConnection Click Properties Click Network ConnectionsRight-click Local Area Click OK Double-click InternetProtocol TCP/IP Select Obtain an IP address automatically Select Obtain DNS server address automaticallyTD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Click Properties For Windows Vista OSClick View network status and tasks Click View status Protocol Version 4 TCP/IPv4 Select Obtain an IP address automatically Right-click Local Click View network status and tasks Click Change adapter settingsFor Windows 7 OS Area Connection Click PropertiesSelect Obtain DNS server address automatically 4. What can I do if I cannot access the Internet? Click Internet Options Select Never dial a connection2 Check to see if you can log on to the web management page of the Modem Router. If you can, try the following steps. If you cannot, please set your computer referring to T3 then try to see if you can access the Internet. If the problem persists, please go to the next step Singapore Appendix C Technical Support Technical SupportGlobal USA/Canada