TP-Link td-w8961nd manual TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide

Page 17

Manual background

TD-W8961ND300Mbps Wireless N ADSL2+ Modem Router User Guide

Figure 3-2

Step 3: Select General tab, highlight Internet Protocol (TCP/IP), and then click the Properties button.

Figure 3-3

10

Image 17

Contents Rev 2.0.0 TD-W8961ND 300Mbps Wireless N ADSL2+ Modem RouterCOPYRIGHT & TRADEMARKS FCC STATEMENT FCC RF Radiation Exposure StatementNational Restrictions CE Mark WarningCountry RestrictionProduct Description 300Mbps Wireless N ADSL2+ Modem Router DECLARATION OF CONFORMITYShenzhen, P. R. China ETSI EN 300 328 V1.7.1Hardware Installation Package ContentsQuick Installation Guide Software ConfigurationAppendix B Troubleshooting Appendix A SpecificationsAppendix C Technical Support MaintenanceTD-W8961ND Package Contents300Mbps Wireless N ADSL2+ Modem Router User Guide Wireless 1.2 Main FeaturesChapter 1 Introduction 1.1 Product OverviewTD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide 1.3 Conventions2.1 The Front Panel Chapter 2 Hardware InstallationLED Explanation Name1. If the ADSL LED is off, please check your Internet connection first. Refer to 2.4 Connecting the Router for more information about how to make Internet connection correctly. If you have already made a right connection, please contact your ISP to make sure if your Internet service is available now 2.2 The Back Panel Back to LED Explanation 2.3 Installation Environment2.4 Connecting the Router TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide 3.1 Configure PC Chapter 3 Quick Installation GuideTD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Step 4 Configure the IP address as Figure 3-4 shows. After that, click OK 1 Is the connection between your PC and the Router correct? 3.2 Login2 Is the TCP/IP configuration for your PC correct? and Connection Type. Then click NEXT Step 1 Select the Quick Start tab, then click RUN WIZARD, and you will see the next screen. Click the NEXT buttonStep 6 Click NEXT to finish the Quick Start Step 5 Configure the rules for the WLAN, and click NEXT4.1.1 Device Info Chapter 4 Software Configuration4.1 Status 4.1.2 System Log Click the SAVE LOG button to save the logs 4.1.3 StatisticsClick the CLEAR LOG button to clear the logs Statistics Table ¾ Select Ethernet, and you will see the statistics table as belowPlease refer to 3.2 Login 4.2 Quick Start¾ Select ADSL, and you will see the statistics table as below ¾ Select WLAN, and you will see the statistics table as below4.3.1 Internet 4.3 Interface Setup1 Dynamic IP Address 2 Static IP Address 3 PPPoA/PPPoE 4 Bridge Mode 4.3.2 LANTD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide IGMP Snoop Enable the IGMP Snoop function if you need If you select Disabled, the DHCP function will not take effect How to assign a static IP address to the client?4.3.3 Wireless TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide ¾ Multiple SSIDs Settings These are the settings of the SSID 1 WEP- 64Bits 3 WPA-PSK 2 WEP-128Bits5 WPA-PSK/WPA2-PSK 4 WPA2-PSKMethod One 4.3.3.1 WPS Settings1 PBC Method Two 2 PIN code TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User GuideTD-W8961ND 4.4.1 Firewall 4.4 Advanced Setup4.4.2 Routing 4.4.3 NAT 4.4.3.2 Virtual Server 4.4.3.1 DMZ4.4.3.3 IP Address Mapping To add a virtual server entryOther operations for the entries as shown in Figure IP Address Mapping is only available for VCs with Multiple IPs 4.4.4 QoSTo add a mapping rule ¾ Summary Click the button to view the configurations of QoS 4.4.5 VLAN 2 Define VLAN Group 1 Assign VLAN PVID for each Interface4.4.6 ADSL 4.5.1 ACL 4.5 Access Management4.5.2.1 IP Filter 4.5.2 Filter¾ Interface Select the interface for the entry To add an IP Address filtering entry Step 5 Finally, click the SAVE to save the entry To add a MAC Address filtering entry 4.5.2.2 MAC Filter4.5.2.3 Application Filter Select the “MAC” as the Rule Type on the Filter screen show in Figure4.5.2.4 URL Filter To add a URL filter entry 4.5.4 UPnP 4.5.3 SNMP4.5.6 CWMP 4.5.5 DDNS4.6 Maintenance 1 NTP Server automatically 4.6.1 Administration4.6.2 Time Zone 3 Manually 2 PC’s ClockTo upgrade the routers firmware, follow these instructions below 4.6.3 FirmwareTo restore the Router’s settings 3 The router will reboot after the upgrading has been finishedTo back up the Router’s current settings 4.6.4 SysRestart 4.6.5 Diagnostics4.7 Help TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Physical and Environment Appendix A SpecificationsGeneral 2. What can I do if I don’t know or forgot my password? Appendix B Troubleshooting3. What can I do if I cannot access the web-based configuration page? For Windows XP OSConnection Click Properties Click Network ConnectionsRight-click Local Area Protocol TCP/IP Select Obtain an IP address automatically Double-click InternetClick OK Select Obtain DNS server address automaticallyClick OK Click Properties For Windows Vista OSClick View network status and tasks Click View status Protocol Version 4 TCP/IPv4 Select Obtain an IP address automatically For Windows 7 OS Click View network status and tasks Click Change adapter settingsRight-click Local Area Connection Click PropertiesSelect Obtain DNS server address automatically Click Internet Options Select Never dial a connection 4. What can I do if I cannot access the Internet?2 Check to see if you can log on to the web management page of the Modem Router. If you can, try the following steps. If you cannot, please set your computer referring to T3 then try to see if you can access the Internet. If the problem persists, please go to the next step Global Appendix C Technical Support Technical SupportSingapore USA/Canada