TP-Link td-w8961nd manual TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide

Page 32

Manual background

TD-W8961ND300Mbps Wireless N ADSL2+ Modem Router User Guide

Figure 4-11

¾Router Local IP: These are the IP settings of the LAN interface for the device. These settings may be referred to as Private settings. You may change the LAN IP address if needed. The LAN IP address is private to your internal network and cannot be seen on the Internet.

•IP Address: Enter the Router’s local IP Address, then you can access to the Web-based Utility via the IP Address, the default value is 192.168.1.1.

•IP Subnet Mask: Enter the Router’s Subnet Mask, the default value is 255.255.255.0.

•Dynamic Route: Select this option to specify the RIP (Routing Information protocol) version for LAN interface, including RIP1, RIP2-Band RIP2-M. RIP2-B and RIP2-M are both sent in RIP2 format, the difference is that RIP2-M using Multicast, while RIP2-B using Broadcast format.

•Direction: Select this option to specify the RIP direction. None is for disabling the RIP function. Both means the ADSL Router will periodically send routing information and accept routing information, and then incorporate them into routing table. IN only means the ADSL router will only accept but will not send RIP packet. OUT only means the ADSL router will only send but will not accept RIP packet.

25

Image 32

Contents TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router Rev 2.0.0COPYRIGHT & TRADEMARKS FCC RF Radiation Exposure Statement FCC STATEMENTCE Mark Warning National RestrictionsCountry RestrictionDECLARATION OF CONFORMITY Product Description 300Mbps Wireless N ADSL2+ Modem RouterShenzhen, P. R. China ETSI EN 300 328 V1.7.1Package Contents Hardware InstallationQuick Installation Guide Software ConfigurationAppendix A Specifications Appendix B TroubleshootingAppendix C Technical Support MaintenanceTD-W8961ND Package Contents300Mbps Wireless N ADSL2+ Modem Router User Guide 1.2 Main Features WirelessChapter 1 Introduction 1.1 Product Overview1.3 Conventions TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User GuideChapter 2 Hardware Installation 2.1 The Front PanelLED Explanation Name1. If the ADSL LED is off, please check your Internet connection first. Refer to 2.4 Connecting the Router for more information about how to make Internet connection correctly. If you have already made a right connection, please contact your ISP to make sure if your Internet service is available now 2.2 The Back Panel Back to LED Explanation 2.3 Installation Environment2.4 Connecting the Router TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Chapter 3 Quick Installation Guide 3.1 Configure PCTD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Step 4 Configure the IP address as Figure 3-4 shows. After that, click OK 1 Is the connection between your PC and the Router correct? 3.2 Login2 Is the TCP/IP configuration for your PC correct? Step 1 Select the Quick Start tab, then click RUN WIZARD, and you will see the next screen. Click the NEXT button and Connection Type. Then click NEXTStep 5 Configure the rules for the WLAN, and click NEXT Step 6 Click NEXT to finish the Quick Start4.1.1 Device Info Chapter 4 Software Configuration4.1 Status 4.1.2 System Log Click the SAVE LOG button to save the logs 4.1.3 StatisticsClick the CLEAR LOG button to clear the logs ¾ Select Ethernet, and you will see the statistics table as below Statistics Table4.2 Quick Start Please refer to 3.2 Login¾ Select ADSL, and you will see the statistics table as below ¾ Select WLAN, and you will see the statistics table as below4.3 Interface Setup 4.3.1 Internet1 Dynamic IP Address 2 Static IP Address 3 PPPoA/PPPoE 4.3.2 LAN 4 Bridge ModeTD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide IGMP Snoop Enable the IGMP Snoop function if you need How to assign a static IP address to the client? If you select Disabled, the DHCP function will not take effect4.3.3 Wireless TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide ¾ Multiple SSIDs Settings These are the settings of the SSID 1 WEP- 64Bits 2 WEP-128Bits 3 WPA-PSK4 WPA2-PSK 5 WPA-PSK/WPA2-PSKMethod One 4.3.3.1 WPS Settings1 PBC Method Two 2 PIN code 300Mbps Wireless N ADSL2+ Modem Router User Guide TD-W8961ND300Mbps Wireless N ADSL2+ Modem Router User Guide 4.4 Advanced Setup 4.4.1 Firewall4.4.2 Routing 4.4.3 NAT 4.4.3.1 DMZ 4.4.3.2 Virtual Server4.4.3.3 IP Address Mapping To add a virtual server entryOther operations for the entries as shown in Figure IP Address Mapping is only available for VCs with Multiple IPs 4.4.4 QoSTo add a mapping rule ¾ Summary Click the button to view the configurations of QoS 4.4.5 VLAN 1 Assign VLAN PVID for each Interface 2 Define VLAN Group4.4.6 ADSL 4.5 Access Management 4.5.1 ACL4.5.2 Filter 4.5.2.1 IP Filter¾ Interface Select the interface for the entry To add an IP Address filtering entry Step 5 Finally, click the SAVE to save the entry 4.5.2.2 MAC Filter To add a MAC Address filtering entrySelect the “MAC” as the Rule Type on the Filter screen show in Figure 4.5.2.3 Application Filter4.5.2.4 URL Filter To add a URL filter entry 4.5.3 SNMP 4.5.4 UPnP4.5.5 DDNS 4.5.6 CWMP4.6 Maintenance 1 NTP Server automatically 4.6.1 Administration4.6.2 Time Zone 2 PC’s Clock 3 Manually4.6.3 Firmware To upgrade the routers firmware, follow these instructions belowTo restore the Router’s settings 3 The router will reboot after the upgrading has been finishedTo back up the Router’s current settings 4.6.5 Diagnostics 4.6.4 SysRestart4.7 Help TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Physical and Environment Appendix A SpecificationsGeneral Appendix B Troubleshooting 2. What can I do if I don’t know or forgot my password?3. What can I do if I cannot access the web-based configuration page? For Windows XP OSConnection Click Properties Click Network ConnectionsRight-click Local Area Double-click Internet Protocol TCP/IP Select Obtain an IP address automaticallyClick OK Select Obtain DNS server address automaticallyTD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Click Properties For Windows Vista OSClick View network status and tasks Click View status Protocol Version 4 TCP/IPv4 Select Obtain an IP address automatically Click View network status and tasks Click Change adapter settings For Windows 7 OSRight-click Local Area Connection Click PropertiesSelect Obtain DNS server address automatically 4. What can I do if I cannot access the Internet? Click Internet Options Select Never dial a connection2 Check to see if you can log on to the web management page of the Modem Router. If you can, try the following steps. If you cannot, please set your computer referring to T3 then try to see if you can access the Internet. If the problem persists, please go to the next step Appendix C Technical Support Technical Support GlobalSingapore USA/Canada