TP-Link td-w8961nd manual 4.3.2 LAN, TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide

Page 31

4)Bridge Mode

TD-W8961ND300Mbps Wireless N ADSL2+ Modem Router User Guide

¾Connection: For PPPoA/PPPoE connection, you can select Always on or Connect on-Demandor Connect Manually. Connect on demand is dependent on the traffic. If there is no traffic (or Idle) for a pre-specified period of time), the connection will tear down automatically. And once there is traffic send or receive, the connection will be automatically on.

¾Static/Dynamic IP Address: For PPPoA/PPPoE connection, you need to specify the public IP address for this ADSL Router. The IP address can be either dynamically (via DHCP) or given IP address provided by your ISP. For Static IP, you need to specify the IP address, Subnet Mask and Gateway IP address.

¾Default Route: You should select Yes to configure the PVC as the default gateway to internet from this device.

¾MAC Spoofing: Enable the MAC Spoofing, and enter a MAC address to configure the WAN port. It makes your inside network appear as a device with this MAC address to the outside world.

4)Bridge Mode

If you select this type of connection, the modem can be configured to act as a bridging device between your LAN and your ISP. Bridges are devices that enable two or more networks to communicate as if they are two segments of the same physical LAN.

Figure 4-10

)Note:

After you finish the Internet configuration, please click SAVE to make the settings take effect.

4.3.2 LAN

Choose “Interface Setup→LAN” menu, and you will see the LAN screen (shown in Figure 4-11). Please configure the parameters for LAN ports according to the descriptions below.

24

Image 31

Contents Rev 2.0.0 TD-W8961ND 300Mbps Wireless N ADSL2+ Modem RouterCOPYRIGHT & TRADEMARKS FCC STATEMENT FCC RF Radiation Exposure StatementRestriction CE Mark WarningNational Restrictions CountryETSI EN 300 328 V1.7.1 DECLARATION OF CONFORMITYProduct Description 300Mbps Wireless N ADSL2+ Modem Router Shenzhen, P. R. ChinaSoftware Configuration Package ContentsHardware Installation Quick Installation GuideMaintenance Appendix A SpecificationsAppendix B Troubleshooting Appendix C Technical Support300Mbps Wireless N ADSL2+ Modem Router User Guide Package ContentsTD-W8961ND 1.1 Product Overview 1.2 Main FeaturesWireless Chapter 1 IntroductionTD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide 1.3 ConventionsName Chapter 2 Hardware Installation2.1 The Front Panel LED Explanation1. If the ADSL LED is off, please check your Internet connection first. Refer to 2.4 Connecting the Router for more information about how to make Internet connection correctly. If you have already made a right connection, please contact your ISP to make sure if your Internet service is available now 2.2 The Back Panel 2.4 Connecting the Router 2.3 Installation EnvironmentBack to LED Explanation TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide 3.1 Configure PC Chapter 3 Quick Installation GuideTD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Step 4 Configure the IP address as Figure 3-4 shows. After that, click OK 2 Is the TCP/IP configuration for your PC correct? 3.2 Login1 Is the connection between your PC and the Router correct? and Connection Type. Then click NEXT Step 1 Select the Quick Start tab, then click RUN WIZARD, and you will see the next screen. Click the NEXT buttonStep 6 Click NEXT to finish the Quick Start Step 5 Configure the rules for the WLAN, and click NEXT4.1 Status Chapter 4 Software Configuration4.1.1 Device Info 4.1.2 System Log Click the CLEAR LOG button to clear the logs 4.1.3 StatisticsClick the SAVE LOG button to save the logs Statistics Table ¾ Select Ethernet, and you will see the statistics table as below¾ Select WLAN, and you will see the statistics table as below 4.2 Quick StartPlease refer to 3.2 Login ¾ Select ADSL, and you will see the statistics table as below4.3.1 Internet 4.3 Interface Setup1 Dynamic IP Address 2 Static IP Address 3 PPPoA/PPPoE 4 Bridge Mode 4.3.2 LANTD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide IGMP Snoop Enable the IGMP Snoop function if you need If you select Disabled, the DHCP function will not take effect How to assign a static IP address to the client?4.3.3 Wireless TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide ¾ Multiple SSIDs Settings These are the settings of the SSID 1 WEP- 64Bits 3 WPA-PSK 2 WEP-128Bits5 WPA-PSK/WPA2-PSK 4 WPA2-PSK1 PBC 4.3.3.1 WPS SettingsMethod One Method Two 2 PIN code TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User GuideTD-W8961ND 4.4.1 Firewall 4.4 Advanced Setup4.4.2 Routing 4.4.3 NAT 4.4.3.2 Virtual Server 4.4.3.1 DMZOther operations for the entries as shown in Figure To add a virtual server entry4.4.3.3 IP Address Mapping To add a mapping rule 4.4.4 QoSIP Address Mapping is only available for VCs with Multiple IPs ¾ Summary Click the button to view the configurations of QoS 4.4.5 VLAN 2 Define VLAN Group 1 Assign VLAN PVID for each Interface4.4.6 ADSL 4.5.1 ACL 4.5 Access Management4.5.2.1 IP Filter 4.5.2 Filter¾ Interface Select the interface for the entry To add an IP Address filtering entry Step 5 Finally, click the SAVE to save the entry To add a MAC Address filtering entry 4.5.2.2 MAC Filter4.5.2.3 Application Filter Select the “MAC” as the Rule Type on the Filter screen show in Figure4.5.2.4 URL Filter To add a URL filter entry 4.5.4 UPnP 4.5.3 SNMP4.5.6 CWMP 4.5.5 DDNS4.6 Maintenance 4.6.2 Time Zone 4.6.1 Administration1 NTP Server automatically 3 Manually 2 PC’s ClockTo upgrade the routers firmware, follow these instructions below 4.6.3 FirmwareTo back up the Router’s current settings 3 The router will reboot after the upgrading has been finishedTo restore the Router’s settings 4.6.4 SysRestart 4.6.5 Diagnostics4.7 Help TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide General Appendix A SpecificationsPhysical and Environment For Windows XP OS Appendix B Troubleshooting2. What can I do if I don’t know or forgot my password? 3. What can I do if I cannot access the web-based configuration page?Right-click Local Area Click Network ConnectionsConnection Click Properties Select Obtain DNS server address automatically Double-click InternetProtocol TCP/IP Select Obtain an IP address automatically Click OKClick OK Click View network status and tasks Click View status For Windows Vista OSClick Properties Protocol Version 4 TCP/IPv4 Select Obtain an IP address automatically Area Connection Click Properties Click View network status and tasks Click Change adapter settingsFor Windows 7 OS Right-click LocalSelect Obtain DNS server address automatically Click Internet Options Select Never dial a connection 4. What can I do if I cannot access the Internet?2 Check to see if you can log on to the web management page of the Modem Router. If you can, try the following steps. If you cannot, please set your computer referring to T3 then try to see if you can access the Internet. If the problem persists, please go to the next step USA/Canada Appendix C Technical Support Technical SupportGlobal Singapore