TP-Link td-w8961nd TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide, For Windows 7 OS

Page 82
For Windows 7 OS

TD-W8961ND300Mbps Wireless N ADSL2+ Modem Router User Guide

For Windows 7 OS

Go to Start > Settings > Control Panel, and then you will see the following page.

Click View network status and tasks

Click Change adapter settings

Right-click Local

Area Connection

Click Properties

75

Image 82
Contents TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router Rev 2.0.0COPYRIGHT & TRADEMARKS FCC RF Radiation Exposure Statement FCC STATEMENTCountry CE Mark WarningNational Restrictions RestrictionShenzhen, P. R. China DECLARATION OF CONFORMITYProduct Description 300Mbps Wireless N ADSL2+ Modem Router ETSI EN 300 328 V1.7.1Quick Installation Guide Package ContentsHardware Installation Software ConfigurationAppendix C Technical Support Appendix A SpecificationsAppendix B Troubleshooting Maintenance300Mbps Wireless N ADSL2+ Modem Router User Guide Package ContentsTD-W8961ND Chapter 1 Introduction 1.2 Main FeaturesWireless 1.1 Product Overview1.3 Conventions TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User GuideLED Explanation Chapter 2 Hardware Installation2.1 The Front Panel Name1. If the ADSL LED is off, please check your Internet connection first. Refer to 2.4 Connecting the Router for more information about how to make Internet connection correctly. If you have already made a right connection, please contact your ISP to make sure if your Internet service is available now 2.2 The Back Panel 2.4 Connecting the Router 2.3 Installation EnvironmentBack to LED Explanation TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Chapter 3 Quick Installation Guide 3.1 Configure PCTD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Step 4 Configure the IP address as Figure 3-4 shows. After that, click OK 2 Is the TCP/IP configuration for your PC correct? 3.2 Login1 Is the connection between your PC and the Router correct? Step 1 Select the Quick Start tab, then click RUN WIZARD, and you will see the next screen. Click the NEXT button and Connection Type. Then click NEXTStep 5 Configure the rules for the WLAN, and click NEXT Step 6 Click NEXT to finish the Quick Start4.1 Status Chapter 4 Software Configuration4.1.1 Device Info 4.1.2 System Log Click the CLEAR LOG button to clear the logs 4.1.3 StatisticsClick the SAVE LOG button to save the logs ¾ Select Ethernet, and you will see the statistics table as below Statistics Table¾ Select ADSL, and you will see the statistics table as below 4.2 Quick StartPlease refer to 3.2 Login ¾ Select WLAN, and you will see the statistics table as below4.3 Interface Setup 4.3.1 Internet1 Dynamic IP Address 2 Static IP Address 3 PPPoA/PPPoE 4.3.2 LAN 4 Bridge ModeTD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide IGMP Snoop Enable the IGMP Snoop function if you need How to assign a static IP address to the client? If you select Disabled, the DHCP function will not take effect4.3.3 Wireless TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide ¾ Multiple SSIDs Settings These are the settings of the SSID 1 WEP- 64Bits 2 WEP-128Bits 3 WPA-PSK4 WPA2-PSK 5 WPA-PSK/WPA2-PSK1 PBC 4.3.3.1 WPS SettingsMethod One Method Two 2 PIN code 300Mbps Wireless N ADSL2+ Modem Router User Guide TD-W8961ND300Mbps Wireless N ADSL2+ Modem Router User Guide 4.4 Advanced Setup 4.4.1 Firewall4.4.2 Routing 4.4.3 NAT 4.4.3.1 DMZ 4.4.3.2 Virtual ServerOther operations for the entries as shown in Figure To add a virtual server entry4.4.3.3 IP Address Mapping To add a mapping rule 4.4.4 QoSIP Address Mapping is only available for VCs with Multiple IPs ¾ Summary Click the button to view the configurations of QoS 4.4.5 VLAN 1 Assign VLAN PVID for each Interface 2 Define VLAN Group4.4.6 ADSL 4.5 Access Management 4.5.1 ACL4.5.2 Filter 4.5.2.1 IP Filter¾ Interface Select the interface for the entry To add an IP Address filtering entry Step 5 Finally, click the SAVE to save the entry 4.5.2.2 MAC Filter To add a MAC Address filtering entrySelect the “MAC” as the Rule Type on the Filter screen show in Figure 4.5.2.3 Application Filter4.5.2.4 URL Filter To add a URL filter entry 4.5.3 SNMP 4.5.4 UPnP4.5.5 DDNS 4.5.6 CWMP4.6 Maintenance 4.6.2 Time Zone 4.6.1 Administration1 NTP Server automatically 2 PC’s Clock 3 Manually4.6.3 Firmware To upgrade the routers firmware, follow these instructions belowTo back up the Router’s current settings 3 The router will reboot after the upgrading has been finishedTo restore the Router’s settings 4.6.5 Diagnostics 4.6.4 SysRestart4.7 Help TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide General Appendix A SpecificationsPhysical and Environment 3. What can I do if I cannot access the web-based configuration page? Appendix B Troubleshooting2. What can I do if I don’t know or forgot my password? For Windows XP OSRight-click Local Area Click Network ConnectionsConnection Click Properties Click OK Double-click InternetProtocol TCP/IP Select Obtain an IP address automatically Select Obtain DNS server address automaticallyTD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Click View network status and tasks Click View status For Windows Vista OSClick Properties Protocol Version 4 TCP/IPv4 Select Obtain an IP address automatically Right-click Local Click View network status and tasks Click Change adapter settingsFor Windows 7 OS Area Connection Click PropertiesSelect Obtain DNS server address automatically 4. What can I do if I cannot access the Internet? Click Internet Options Select Never dial a connection2 Check to see if you can log on to the web management page of the Modem Router. If you can, try the following steps. If you cannot, please set your computer referring to T3 then try to see if you can access the Internet. If the problem persists, please go to the next step Singapore Appendix C Technical Support Technical SupportGlobal USA/Canada