TP-Link td-w8961nd manual TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide

Page 50

To add a virtual server entry:

TD-W8961ND300Mbps Wireless N ADSL2+ Modem Router User Guide

example, if you want to set the FTP Virtual server, you can set the start and end port number to 21.

¾Local IP Address: Enter the IP Address for the Virtual Server in LAN side.

¾Virtual Server Listing: This displays the information about the Virtual Servers you establish.

To add a virtual server entry:

Step 1: Select the “Virtual Circuit” and select “Virtual Server”.

)Note:

For VCs with single IP, select Single; For VCs with multiple IPs, select Multiple for the option. Step 2: Select the Rule index for the rule as shown in Figure 4-30.

Step 3: Select the application you want from drop-down list, then the protocol and port number will be added to the corresponding field automatically, you only need to configure the IP address for the virtual server; If the application list does not contain the service that you want, please configure the Port number, IP Address and Protocol manually.

Step 4: After that, click SAVE to make the entry take effect.

Other operations for the entries as shown in Figure 4-30:

Enter the index of assigned entry, and click the DELETE button to delete the entry. Click the BACK button to return to the previous screen.

Click the CANCEL button to cancel the configuration which is made just now.

4.4.3.3 IP Address Mapping

Select Multiple for numbers of IPs in Figure 4-28,and choose “Advanced Setup→NAT→IP Address Mapping(for Multiple IP Service)”. You can configure the Address Mapping Rule in the next screen. The IP Address Mapping is for those VCs that configured with multiple IPs. The IP Address Mapping rule is per-VC based (only for Multiple IPs' VCs).

Figure 4-31

¾Rule Index: Select the Virtual server rule index for this VC. You can specify 8 rules in maximum.

¾Rule Typ: There are four types: one-to-one, Many-to-One, Many-to-Many Overload and Many-to-Many No-overload.

43

Image 50

Contents TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router Rev 2.0.0COPYRIGHT & TRADEMARKS FCC RF Radiation Exposure Statement FCC STATEMENTCountry CE Mark WarningNational Restrictions RestrictionShenzhen, P. R. China DECLARATION OF CONFORMITYProduct Description 300Mbps Wireless N ADSL2+ Modem Router ETSI EN 300 328 V1.7.1Quick Installation Guide Package ContentsHardware Installation Software ConfigurationAppendix C Technical Support Appendix A SpecificationsAppendix B Troubleshooting MaintenanceTD-W8961ND Package Contents300Mbps Wireless N ADSL2+ Modem Router User Guide Chapter 1 Introduction 1.2 Main FeaturesWireless 1.1 Product Overview1.3 Conventions TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User GuideLED Explanation Chapter 2 Hardware Installation2.1 The Front Panel Name1. If the ADSL LED is off, please check your Internet connection first. Refer to 2.4 Connecting the Router for more information about how to make Internet connection correctly. If you have already made a right connection, please contact your ISP to make sure if your Internet service is available now 2.2 The Back Panel Back to LED Explanation 2.3 Installation Environment2.4 Connecting the Router TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Chapter 3 Quick Installation Guide 3.1 Configure PCTD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Step 4 Configure the IP address as Figure 3-4 shows. After that, click OK 1 Is the connection between your PC and the Router correct? 3.2 Login2 Is the TCP/IP configuration for your PC correct? Step 1 Select the Quick Start tab, then click RUN WIZARD, and you will see the next screen. Click the NEXT button and Connection Type. Then click NEXTStep 5 Configure the rules for the WLAN, and click NEXT Step 6 Click NEXT to finish the Quick Start4.1.1 Device Info Chapter 4 Software Configuration4.1 Status 4.1.2 System Log Click the SAVE LOG button to save the logs 4.1.3 StatisticsClick the CLEAR LOG button to clear the logs ¾ Select Ethernet, and you will see the statistics table as below Statistics Table¾ Select ADSL, and you will see the statistics table as below 4.2 Quick StartPlease refer to 3.2 Login ¾ Select WLAN, and you will see the statistics table as below4.3 Interface Setup 4.3.1 Internet1 Dynamic IP Address 2 Static IP Address 3 PPPoA/PPPoE 4.3.2 LAN 4 Bridge ModeTD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide IGMP Snoop Enable the IGMP Snoop function if you need How to assign a static IP address to the client? If you select Disabled, the DHCP function will not take effect4.3.3 Wireless TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide ¾ Multiple SSIDs Settings These are the settings of the SSID 1 WEP- 64Bits 2 WEP-128Bits 3 WPA-PSK4 WPA2-PSK 5 WPA-PSK/WPA2-PSKMethod One 4.3.3.1 WPS Settings1 PBC Method Two 2 PIN code 300Mbps Wireless N ADSL2+ Modem Router User Guide TD-W8961ND300Mbps Wireless N ADSL2+ Modem Router User Guide 4.4 Advanced Setup 4.4.1 Firewall4.4.2 Routing 4.4.3 NAT 4.4.3.1 DMZ 4.4.3.2 Virtual Server4.4.3.3 IP Address Mapping To add a virtual server entryOther operations for the entries as shown in Figure IP Address Mapping is only available for VCs with Multiple IPs 4.4.4 QoSTo add a mapping rule ¾ Summary Click the button to view the configurations of QoS 4.4.5 VLAN 1 Assign VLAN PVID for each Interface 2 Define VLAN Group4.4.6 ADSL 4.5 Access Management 4.5.1 ACL4.5.2 Filter 4.5.2.1 IP Filter¾ Interface Select the interface for the entry To add an IP Address filtering entry Step 5 Finally, click the SAVE to save the entry 4.5.2.2 MAC Filter To add a MAC Address filtering entrySelect the “MAC” as the Rule Type on the Filter screen show in Figure 4.5.2.3 Application Filter4.5.2.4 URL Filter To add a URL filter entry 4.5.3 SNMP 4.5.4 UPnP4.5.5 DDNS 4.5.6 CWMP4.6 Maintenance 1 NTP Server automatically 4.6.1 Administration4.6.2 Time Zone 2 PC’s Clock 3 Manually4.6.3 Firmware To upgrade the routers firmware, follow these instructions belowTo restore the Router’s settings 3 The router will reboot after the upgrading has been finishedTo back up the Router’s current settings 4.6.5 Diagnostics 4.6.4 SysRestart4.7 Help TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Physical and Environment Appendix A SpecificationsGeneral 3. What can I do if I cannot access the web-based configuration page? Appendix B Troubleshooting2. What can I do if I don’t know or forgot my password? For Windows XP OSConnection Click Properties Click Network ConnectionsRight-click Local Area Click OK Double-click InternetProtocol TCP/IP Select Obtain an IP address automatically Select Obtain DNS server address automaticallyTD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Click Properties For Windows Vista OSClick View network status and tasks Click View status Protocol Version 4 TCP/IPv4 Select Obtain an IP address automatically Right-click Local Click View network status and tasks Click Change adapter settingsFor Windows 7 OS Area Connection Click PropertiesSelect Obtain DNS server address automatically 4. What can I do if I cannot access the Internet? Click Internet Options Select Never dial a connection2 Check to see if you can log on to the web management page of the Modem Router. If you can, try the following steps. If you cannot, please set your computer referring to T3 then try to see if you can access the Internet. If the problem persists, please go to the next step Singapore Appendix C Technical Support Technical SupportGlobal USA/Canada