ZyXEL Communications 128L user manual Powering On Your Prestige, Front Panel

Page 30

Figure 3-2 Front Panel

PWR - Comes on as soon as you connect your Prestige to the power supply and switch it to the I (on) position.

TST - Should be blinking if your Prestige is functioning properly.

Line: LNK - Indicates that your Prestige has an ISDN line connected to the WAN interface and it has been successfully initialized.

64K and 128K - The 64K LED will light to indicate a line speed of 64K. The 64K and 128K LED will light to indicate a line speed of 128K.

Ethernet: LNK - Indicates that the Prestige has been successfully connected to the LAN via the Ethernet interface.

TX and RX - Transmit and Receive LEDs will blink to indicate when there is traffic on the LAN.

COL - Indicates that there is transmission collision over the LAN.

SMT - Indicates your Prestige is connected to a terminal emulator via the RS-232 port.

SERVER - Indicates your Prestige is configured as a server.

Powering On Your Prestige

When you power on your Prestige, it will perform several internal tests and will also do an IDSL line initialization. After this initialization, your Prestige will ask you to press ENTER to continue as shown below:

18 Installation

Image 30

Contents ZyXEL ZyXEL Limited Warranty FCC Part 15 Information Copyright 1997 by ZyXELAcknowledgments IiiInformation for Canadian Users Contacting ZyXEL ∙ E-mail Contents Installation ViiiTCP/IP Configuration System Security Index 101 Page Introduction FeaturesEase of Installation IntroductionMultiple Networking Protocol Support Dynamic Host Configuration Protocol DhcpIsdn Digital Subscriber Line Idsl Full Network ManagementApplications For Your Prestige Other ResourcesAdditional Installation Requirements Packing ListIntroduction Introduction Before You Begin Road Map and FlowBefore You Begin Completing the Worksheet Ordering Your Idsl LineCollecting General Setup Information Collecting Idsl InformationCollecting Ethernet Setup Information IP Subnet Mask Number of Host Number of Bits General Setup Information Idsl Setup InformationEthernet Setup Information ∙ IP Address ∙ IP Subnet Mask Before You Begin Installation InstallationConnecting an Idsl Line to your Prestige Connecting Your Computer and Your PrestigeConnecting the RS-232 Cable to your Prestige Connecting an Ethernet Cable to your PrestigeConnecting the Power Adapter to your Prestige Prestige Front PanelPowering On Your Prestige Front PanelPower on Messages Navigating Through the System Management Terminal Interface System Management Terminal Interface Summary Menu Title DescriptionGeneral Setup Menu 1 General SetupWAN Port Setup Ethernet Setup General Ethernet Setup Menu 3.1 General Ethernet SetupTCP/IP Ethernet Setup and Dhcp Menu 3.2 TCP/IP Ethernet SetupInstallation Installation Novell IPX Ethernet Setup Bridge Ethernet SetupInstallation Configuring for Internet Access Configuring for Internet AccessIP Addresses and the Internet Internet Access Configuration Menu 4 Internet Access SetupSingle User Account Configuring for Internet Access Configuration for Single User Account A Single User Account Using the PrestigeConfiguring for Internet Access Configuring for Internet Access Remote Node Configuration Remote Node ConfigurationMenu 11 Remote Node Setup Remote Node Configuration Remote Node Configuration Editing PPP Options Remote Node PPP OptionsRemote Node Configuration TCP/IP Configuration TCP/IP ConfigurationIP Subnet Mask 46 TCP/IP Configuration LAN-to-LAN ApplicationRemote Node Setup Menu 11.3 Remote Node Network Layer Options48 TCP/IP Configuration Sample IP AddressesStatic Route Setup 50 TCP/IP Configuration Static Routing ExampleMenu 12 Static Route Setup Main Menu 52 TCP/IP Configuration IPX Network Environment Novell IPX ConfigurationNovell IPX Configuration Frame TypePrestige on LAN with Server Prestige on LAN without ServerIPX Ethernet Setup Menu 3.3 Novell IPX Ethernet Setup∙ Snap Menu 14.1 Edit Dial-in User Static Route Setup NetWare Servers on Both Sides of the Link Menu 12.2 Edit IPX Static Route Novell IPX Configuration Novell IPX Configuration Bridging Configuration Bridge Ethernet SetupBridging Configuration Bridge Static Route Setup Remote Node Bridging ConfigurationMenu 12.4 Bridge Static Route Bridging Configuration Filter Configuration Filter ConfigurationAbout Filtering Configuring a Filter Set Prestige’s Filter StructureMenu 21 Filter Set Configuration Menu 21.1 Filter Rules Summary Configuring a Filter Rule TCP/IP Filter RuleMenu 21.1.1 TCP/IP Filter Rule Filter Configuration Filter Configuration Generic Filter Rule Menu 21.1.1 Generic Filter RuleFilter Configuration Novell IPX Filter Rule Menu 21.1.3 IPX Filter RuleFilter Configuration Configuring Your Prestige For Snmp Support About SnmpMenu 22 Snmp Configuration Snmp Snmp Configuring the SMT Password System SecuritySystem Security System Security Telnet Configuration and Capabilities About Telnet ConfigurationTelnet Configuration and Capabilities Single Administrator System TimeoutTelnet Capabilities System Maintenance System MaintenanceSystem Status Example of Menu 24.1 System Maintenance Status Terminal Baud Rate Menu 24.2 -System Maintenance Change Terminal Baud Rate Log and TraceView Error Log SyslogDiagnostic Menu 24.4 System Maintenance DiagnosticBackup Configuration Restore Configuration Software UpdateCommand Interpreter Mode Example of uploading RAS using PcplusSystem Maintenance None of the LEDs are on when you power up the Prestige TroubleshootingProblems Starting Up the Prestige Connecting the RS-232 cable, cannot access the SMTIdsl LEDs Not On Problems With the Idsl LineProblems with the LAN Interface Can not Ping any station on the LANProblems Connecting to a Remote Node or ISP Troubleshooting Index See IPXIndex See RIP