Peavey 12/0280304941, CS2000H manual CS 2000H

Page 29

CS® 2000H

SPECIFICATIONS

Rated Power:

Bridged 4 ohms:

2000W @ 1kHz @ <0.1% THD

2 x 2 ohms:

1000W per channel @ 1kHz @ <0.1% THD both channels driven

2 x 4 Ohms:

700W per channel @ 1kHz @ <0.05% THD both channels driven

2 x 8 ohms:

425W per channel @ 1kHz @ <0.05% THD both channels driven

1 x 2 ohms:

1325W per channel @ 1kHz @ <0.1%

THD

1 x 4 Ohms:

825W per channel @ 1kHz @ <0.05%

THD

1 x 8 ohms:

500W per channel @ 1kHz @ <0.05%

THD

Minimum Load Impedance:

2 Ohms

Maximum RMS Voltage Swing:

71 V

Frequency Response:

10 Hz–100 kHz; +0‚ -0.5 dB @ 1W

Power Bandwidth:

10 Hz–35 kHz; +0‚ -3 dB @ rated

4 Ohm power

THD (2 x 2 ohms):

<0.2% @ 700W per channel from 20 Hz–20 kHz

THD (2 x 4 ohms):

<0.1% @ 600W per channel from 20 Hz–20 kHz

THD (2 x 8 ohms):

<0.1% @ 400W per channel from 20 Hz–20 kHz

Input CMRR:

-85 dB @ 1 kHz

Voltage Gain:

x40 (32 dB)

Crosstalk:

>-70 dB @ 1 kHz @ rated power @ 8 Ohms

Crossover:

Third Order State Variable Filters: 18 dB/octave

Frequency Range: 40 Hz–300 Hz

Hum & Noise:

>-108 dB; “A” weighted reference to rated power @ 8 ohms

Slew Rate:

> 15V/us

Damping Factor (8 Ohms):

> 500:1 @ 20 Hz–1 kHz

Phase Response:

+5 to -12 degrees from 20 Hz–20 kHz

Input Sensitivity:

1.32V +/- 3% for 1 kHz @ 4 ohm rated power;

1.12V +/- 3% for 1 kHz @

2 Ohm rated power

Input Impedance:

15 k Ohms‚ balanced

Max Input Power w/typical music program:

950W @ 2 Ohms

660W @ 4 Ohms

Max Input Power w/severe music program:

2400W @ 2 Ohms

1650W @ 4 Ohms

Cooling:

Two front panel temperature- dependent variable speed 80mm high- output DC fans

Controls:

2 front panel attenuators‚ rear panel Mode switch‚ Function switch per channel‚ High Pass adjustable filter per channel. High Pass filter bypass switch per channel‚ adjustable subwoofer crossover per channel.

Indicator LEDs:

2 ACL (clip limiting)‚ 2 Signal presence‚ 2 Active status‚ 2 DC protect‚ 2 Temperature limit

Protection:

Thermal‚ DC‚ turn-on bursts‚ subsonic‚ incorrect loads

Connectors:

Combi XLR & 6.3mm phone input; Speakon and Binding Post speaker output; 6.3mm High Pass or Full Range patch connector per channel; 6.3mm Low Pass patch connector per channel; 15 amp IEC mains connector

Construction:

16 ga. steel with cast aluminum front panel and cast handles

Dimensions:

88.9mm x 483mm x 441mm (3.5" x 19" x 17.375" over all. 406mm (16") inside rack depth

Net Weight:

19.5 kg (43 lbs)

Gross Weight:

20.6 kg (45.5 lbs)

All power measurements made at 120 VAC‚ power transformer cold. 2 Ohm power is time limited by magnetic circuit breaker.

29

Image 29
Contents CS2000H Operations Manual Page Sound Level dBA, Slow Response Important Safety InstructionsUnpacking CS 2000H Power AmplifierMounting Cooling RequirementsR E U G E A R T Operating PrecautionsConnecting Outputs Connecting InputsConnecting Power StereoTemp LED Signal LEDActive LED DDT LEDHigh PASS/FULL Range Output Connector LOW CUT SwitchLOW Pass Output Connector Distortion Detection LimitingAmplifier Maintenance and User Responsibility RampUp Signal ControlShort Circuit DC Voltage ProtectionCS 2000H Block Diagram Glossary of Terms Setup Instructions To Stereo Bi-amp Hookup Diagram CS 2000H Montage CS 2000H VerstärkerAuspacken Sicherheitshinweise für den Betrieb KühlanforderungenAnschluss der Ausgänge Anschluss der EingängeNetzanschluss Wechselstrom-Netzschalter/Sicherungsautomat SIGNAL-LEDEingangsdämpfer Anzeigen auf der VorderseiteDDT-LED TEMP-LEDACTIVE-LED MODE-WahlschalterLOW-CUT-Einstellknopf CROSSOVER-EinstellknopfLOW-CUT-Schalter Stecker High PASS/FULL Range OutputLFC-Impedanzermittlung RampUp-SignalregelungThermoschutz KurzschlussWartung des Verstärkers und Verantwortung des Nutzers LautsprecherschutzErklärung der Begriffe Setup-Anweisungen Mono-Biamp-Betrieb Subwoofer und Mid/High-Box CS 2000H Instalación Amplificador de Poder CS 2000HDesempaque Precauciones de Operación Requisitos de enfriamientoConectando Salidas Conectando EntradasEstéreo Conectando CorrienteParalelo Mono/PuenteAtenuadores de Entrada Interruptor de Corriente/Breaker de CircuitoIndicadores del Panel Frontal LED de SeñalLED de DDT LED de TempLED Activo Interruptor de Función del AmplificadorPerilla de Ajuste LOW CUT Filtro de Graves Perilla de Ajuste del CrossoverInterruptor LOW CUT Filtro de Graves Salida de LOW PassSensibilidad de Impedancia LFC Limitación de Detección de DistorsiónProtección Térmica Cortos CircuitosProtección de Parlantes Control de señal RampUpGlosario de Términos Instrucciones de Instalación Operación Mono Bi-Amp CS 2000H Amplificateurs de Puissance CS 2000H InstallationDéballage RefroidissementPrécautions d’Utilisation Connecter les sorties de votre unité Outputs Connecter les entrées de votre unité InputsAlimentation Electrique StéréoIndicateurs du Panneau Avant AMP Function Switch Mode Select SwitchCrossover Adjustment Knob LOW CUT Adjustment KnobProtection contre le Courant Continu Limite de Détection de DistortionProtection Thermique Protection de Mise Sous/Hors Tension Maintenance et Responsabilité d’UtilisateurSystème RampUp contrôle de montée en puissance Protection des Haut-ParleursGlossaire Instructions D’INSTALLATION Signal Mono Système Bi-Amplification Page Page Product Category Peavey Electronics Corporation Limited Warranty80304941