Dukane 8946 user manual Optimizing RGB Picture Automatically, Turning Up or Down Volume

Page 22

NOTE: During 3D Reform adjustment, "Aspect Ratio" and "Screen" may not be available. Should this happen, first reset the 3D Reform data and then do each setting. Second repeat the 3D Reform adjustment. Changing Aspect Ratio and/ or Screen setting can limit 3D Reform in its adjustable range.

The adjustable ranges for 3D Reform are as follows:

Horizontal

Max ±35° approx.

Vertical

Max +50°/-25° approx.

*The following are conditions at the above maximum angle when all of the following are met

Image is projected in Wide (Zoom)

Resolution is XGA

Higher resolution than XGA limits 3D Reform in its adjustable range.

Menu items should be set as follows:

Aspect Ratio

4:3

Screen Type

4:3

Horizontal and Vertical are adjusted separately.

A combination of both adjustments limits 3D Reform in its adjustable range.

When "4:3 Fill" is selected in Aspect Ratio, "Cornerstone" and "Hori- zontal Keystone" are not available.

Optimizing RGB Picture Automatically

Adjusting the Image Using Auto Adjust

Optimizing RGB image automatically

Press the Auto Adjust button to optimize an RGB image automatically.

[Poor picture]

AUTO ADJ.

[Normal picture]

Turning Up or Down Volume

Sound level from the speaker and the AUDIO OUT jack (RCA) on the projector can be adjusted.

VOLUME

increase volume

decrease volume

Volume bar

Using the Laser Pointer

You can use the laser to draw your audience's attention to a red dot that you can place on any object.

Press and hold the LASER button to activate the laser pointer.

Press the Auto Adjust button to fine-tune the computer image or to re- move any vertical banding that might appear and to reduce video noise, dot interference or cross talk (this is evident when part of your image appears to be shimmering). This function adjusts the clock frequencies that eliminate the horizontal banding in the image. This function also adjusts the clock phase to reduce video noise, dot interference or cross talk. (This is evident when part of your image appears to be shimmer- ing.)

This adjustment may be necessary when you connect your computer for the first time.

NOTE:

Some signals may not be displayed correctly or take time.

The Auto Adjust function does not work for component and video signal.

If the Auto Adjust operation cannot optimize the RGB signal, try to adjust Clock and Phase manually. See page E-41.

Pressing and holding the AUTO ADJUST button on the cabinet or AUTO ADJ button on the remote control for a minimum of 2 seconds will enable the Auto Focus and the Auto Wall Color Correction feature instead of the Auto Adjust feature.

CAUTION:

Do not look into the laser pointer while it is on.

Do not point the laser beam at a person.

E-22

Image 22
Contents Models 8805 Safety Cautions Lamp Replacement Fire and Shock PrecautionsWhats in the Box? Table of Contents Introduction Features youll enjoyIntroduction to the Projector Attaching the lens cap Part Names of the ProjectorCarrying the Projector Top Features SelectTerminal Panel Features Part Names of the Remote Control On the screen using the SelectSelect Operating Range for Wireless Remote Control Battery InstallationRemote Control Precautions Using the Remote Control in Wired OperationSetting Up the Screen and the Projector Installation and ConnectionsSelecting a Location Wide Tele Connecting to RGB 2 in connectors When Viewing a DVI Digital SignalConnecting Your PC or Macintosh Computer Connecting Your PC with a DVI ConnectorTo RGB Connecting an External MonitorTo connect Scart output RGB Commercially available FemaleOptional 15-pin-to-RCA female×3 cable ADP-CV1 Connecting Your DVD PlayerAudio Equipment Video cable not supplied Audio equipment Connecting Your VCR or Laser Disc PlayerConnecting the Supplied Power Cable VCR/ Laser disc playerTurning on the Projector Projecting AN Image Basic OperationPress the Enter button to execute the selection Selecting a Source Adjusting the Picture Size and PositionAdjust the Tilt Foot Selecting the computer or video sourceFocus When using the remote control or cabinet buttonsUsing Auto Focus Use the Focus Button +/- to obtain the best focusPress the Enter button Screen Use the Select When using the USB connected to the projectorConfirmation screen is displayed Adjusting the Image Using Auto Adjust Turning Up or Down VolumeUsing the Laser Pointer Optimizing RGB Picture AutomaticallyTurning off the Projector Setting the function switchTo turn off the projector Convenient Features Using the Remote Mouse FunctionExecuting the Auto 3D Reform feature Auto 3D ReformSetting Screen of Auto 3D Reform AdjustmentFreezing a Picture Using the PointerGetting the On-line Help Operate the Menus using the USB mouse Using a USB Mouse Using the USB HUB FunctionUsing the middle button on the mouse USB Memory Device or USB Memory Card Reader Support Changing Background LogoMaking Freehand Drawings on a Projected Image ChalkBoard Pen Eraser Drive DragUsing the Viewer Making the Most out of the Viewer FunctionOperating the Viewer Function from the Projector playback When the tool bar is not displayedProjecting slides Viewer Viewing Digital Images Auto Play ModeSwitching to Slides Directly from Other Input Modes PreparationsUsing the PC Card Files Fucntion PC Card Files Deleting Captured ImagesDefault Custom Menu items are Using ON-SCREEN MenuUsing the Menus Basic Menu OperationMenu tree Advanced MenuDefault Source Select Operation Mode SelectCommunication Speed WEP Menu Elements Highlight Title bar Tab Check box Drag Tool barMenu Descriptions & Functions Entering Alphanumeric Characters by Using the MenuSource Select Sound Entry Edit CommandPicture not available for Viewer and LAN Image OptionsPicture Management Projector Options Using Adapting Color Correction Wall Color Correction Palette Menu Setup Resolution manually User can adjust the image display functions HoriHttp server functions are not available during Standby mode Selecting Lamp Mode and Lamp Type Lamp Setting Selecting Aspect Ratio and Position for Screen Screen Selecting Auto FunctionsSetting LAN Mode Network Type required for wireless onlyUses 64-bit datalength for secure transmission WEP for Wireless onlyNications may be monitored by someone Pared to use of 64bit datalength encryptionChanging the menu to Advanced Editing the custom menu Setting a PasswordStatus EntrySecurity To enable Security, use the SelectTo delete PC card data you registered Tools Returning to Factory DefaultHelp Replacing the Lamp MaintenanceTo replace the lamp Cleaning the Cabinet and the Lens CleaningCleaning or Replacing the Filter Reinstall the new filter cover CatchStatus Indicator TroubleshootingPower Indicator Lamp IndicatorImage isn’t square to Common Problems & Solutions Check These ItemsFor more information contact your dealer Page Specifications Model Number 8946 OpticalModel Number 8805 Optical Mini D-Sub 15 Pin Connector Cabinet DimensionsPin Assignments of D-Sub RGB Input Connector Pin No RGB Signal Analog YCbCr SignalCompatible Input Signal List Uxga 1600×1200 is supported for separate sync signal onlyPC Control Codes and Cable Connection PC Control Connector D-SUB 9PUsing Software Keyboard Cable ConnectionPreparation Before Use Operation Using an Http BrowserOverview Handling of the Address for Operation via a BrowserPage Page Orders 676-2485 Phone 762-4040401-8805/8946-00