Dukane 8946 user manual Selecting Lamp Mode and Lamp Type Lamp Setting

Page 48

[Page 5]

Remote Sensor:

This option determines which remote sensors on the projector are enabled in wireless mode.

The options are: front, rear, right, or left. All checked boxes indicate that they can accept the infrared signal from the supplied remote control.

S-Video Mode Select:

This feature is used to select the S-Video signal detection mode. This allows identifying of the S-Video signals with different aspect ratio (16:9 and 4:3).

Off

Does not identify any S-video signal.

S2

Identifies the 16:9 or 4:3 signal.

[Page 6]

Selecting Communication Speed [Communication Speed]:

This feature sets the baud rate of the PC Control port (D-Sub 9 Pin). It supports data rates from 4800 to 38400 bps.

The default is 38400 bps. Select the appropriate baud rate for your equipment to be connected (depending on the equipment, a lower baud rate may be recommended for long cable runs).

Selecting Default Source [Default Source Select]:

You can set the projector to default to any one of its inputs each time the projector is turned on.

Last

Sets the projector to default to the previous or last

 

active input each time the projector is turned on.

Auto

Searches for an active source in order of RGB1

 

RGB2 Video S-Video DVI(DIGITAL) Viewer

 

RGB1 and displays the first found source.

Select

Displays the selected source input every time the pro-

 

jector is started up. Select an input from the pull-down

 

menu.

Disabling the Cabinet Buttons [Control Panel Key Lock]:

This option turns on or off the Control Panel Key Lock function.

NOTE:

*This Control Panel Key Lock does not affect the remote control and the PC Control functions.

*When the cabinet buttons are disabled, pressing and holding the CANCEL button for about 10 seconds will change the setting to enabled.

Selecting Lamp Mode and Lamp Type [Lamp Setting]

Lamp Mode:

This feature enables you to select two brightness modes of the lamp: Normal and Eco modes. The lamp life can be extended by using the Eco mode.

Normal Mode . This is the default setting (100% Brightness).

Eco Mode

Select this mode to increase the lamp life (80% Bright-

 

ness).

Lamp Type:

The lamp type you use is displayed here.

456-8946

......... Standard life lamp (8946)

456-8805

......... Standard life lamp (8805)

MT60LPS

....... Optional extended life lamp. When the optional ex-

 

tended life lamp is used, the Lamp Mode is available.

E-48

Image 48
Contents Models 8805 Safety Cautions Fire and Shock Precautions Lamp ReplacementWhats in the Box? Table of Contents Features youll enjoy IntroductionIntroduction to the Projector Part Names of the Projector Attaching the lens capCarrying the Projector Top Features SelectTerminal Panel Features Part Names of the Remote Control On the screen using the SelectSelect Battery Installation Remote Control PrecautionsOperating Range for Wireless Remote Control Using the Remote Control in Wired OperationInstallation and Connections Setting Up the Screen and the ProjectorSelecting a Location Wide Tele When Viewing a DVI Digital Signal Connecting Your PC or Macintosh ComputerConnecting to RGB 2 in connectors Connecting Your PC with a DVI ConnectorConnecting an External Monitor To connect Scart output RGBTo RGB Commercially available FemaleConnecting Your DVD Player Optional 15-pin-to-RCA female×3 cable ADP-CV1Audio Equipment Connecting Your VCR or Laser Disc Player Connecting the Supplied Power CableVideo cable not supplied Audio equipment VCR/ Laser disc playerProjecting AN Image Basic Operation Turning on the ProjectorPress the Enter button to execute the selection Adjusting the Picture Size and Position Adjust the Tilt FootSelecting a Source Selecting the computer or video sourceWhen using the remote control or cabinet buttons Using Auto FocusFocus Use the Focus Button +/- to obtain the best focusWhen using the USB connected to the projector Press the Enter button Screen Use the SelectConfirmation screen is displayed Turning Up or Down Volume Using the Laser PointerAdjusting the Image Using Auto Adjust Optimizing RGB Picture AutomaticallySetting the function switch Turning off the ProjectorTo turn off the projector Convenient Features Using the Remote Mouse FunctionExecuting the Auto 3D Reform feature Auto 3D ReformSetting Screen of Auto 3D Reform AdjustmentUsing the Pointer Freezing a PictureGetting the On-line Help Using a USB Mouse Using the USB HUB Function Operate the Menus using the USB mouseUsing the middle button on the mouse Changing Background Logo Making Freehand Drawings on a Projected Image ChalkBoardUSB Memory Device or USB Memory Card Reader Support Pen Eraser Drive DragUsing the Viewer Making the Most out of the Viewer FunctionWhen the tool bar is not displayed Operating the Viewer Function from the Projector playbackProjecting slides Viewer Auto Play Mode Switching to Slides Directly from Other Input ModesViewing Digital Images PreparationsUsing the PC Card Files Fucntion PC Card Files Deleting Captured ImagesUsing ON-SCREEN Menu Using the MenusDefault Custom Menu items are Basic Menu OperationMenu tree Advanced MenuOperation Mode Select Default Source SelectCommunication Speed WEP Menu Elements Highlight Title bar Tab Check box Drag Tool barEntering Alphanumeric Characters by Using the Menu Menu Descriptions & FunctionsSource Select Entry Edit Command Picture not available for Viewer and LANSound Image OptionsPicture Management Projector Options Using Adapting Color Correction Wall Color Correction Palette Menu Setup User can adjust the image display functions Hori Resolution manuallyHttp server functions are not available during Standby mode Selecting Lamp Mode and Lamp Type Lamp Setting Selecting Aspect Ratio and Position for Screen Screen Selecting Auto FunctionsSetting LAN Mode Network Type required for wireless onlyWEP for Wireless only Nications may be monitored by someoneUses 64-bit datalength for secure transmission Pared to use of 64bit datalength encryptionSetting a Password StatusChanging the menu to Advanced Editing the custom menu EntryTo enable Security, use the Select SecurityTo delete PC card data you registered Returning to Factory Default ToolsHelp Maintenance Replacing the LampTo replace the lamp Cleaning Cleaning or Replacing the FilterCleaning the Cabinet and the Lens Reinstall the new filter cover CatchTroubleshooting Power IndicatorStatus Indicator Lamp IndicatorCommon Problems & Solutions Check These Items Image isn’t square toFor more information contact your dealer Page Specifications Model Number 8946 OpticalModel Number 8805 Optical Cabinet Dimensions Pin Assignments of D-Sub RGB Input ConnectorMini D-Sub 15 Pin Connector Pin No RGB Signal Analog YCbCr SignalCompatible Input Signal List Uxga 1600×1200 is supported for separate sync signal onlyPC Control Connector D-SUB 9P Using Software KeyboardPC Control Codes and Cable Connection Cable ConnectionOperation Using an Http Browser OverviewPreparation Before Use Handling of the Address for Operation via a BrowserPage Page Phone 762-4040 Orders 676-2485401-8805/8946-00