Dukane 8946 Selecting a Source, Adjusting the Picture Size and Position, Adjust the Tilt Foot

Page 19

Selecting a Source

Selecting the computer or video source

Using the Remote Control

OFF

ON

 

POWER

VIDEO

RGB VIEWER

AUTO ADJ.

LASER

Press any one of the RGB, VIDEO or

VIEWER buttons.

ASPECT FREEZE 3D REFORM

HELP POINTER PIC-MUTE

VOLUME MAGNIFY SLIDE

ZOOM FOCUS FOLDER

SLIDE

LIST

Adjusting the Picture Size and Position

Place your projector on a flat level surface and ensure that the projector is square to the screen.

Lift the front edge of the projector to center the image vertically.

Move the projector left to center the image horizontally on the screen.

NOTE: If no input signal is available, the projector will display a blue background (factory preset).

Selecting from Source List

Source List

Press and quickly release the SOURCE button on the projector cabinet to display the Source list. Each time the SOURCE button is pressed, the input source will change as follows: "RGB1", "RGB2" (computer or DVD with component output), "Video" (VCR, document camera, or laser disc player), S-Video", "DVI (Digital)", "Viewer" (slides on a PC card), or "LAN" (wired or wireless signal aired from a PC).

To display the selected source, press the ENTER button.

Detecting the Signal Automatically

Press and hold the SOURCE button for a minimum of 1 second, the projector will search for the next available input source. Each time you press and hold the SOURCE button, the input source will change as follows:

→RGB1 → RGB2 → Video → S-Video → DVI (Digital)→ Viewer

*If the projected image does not appear square to the screen then use the 3D Reform feature for proper adjustment. See page E-20.

Adjust the Tilt Foot

1. Lift the front edge of the projector.

Adjustable Tilt Foot Lever

Adjustable Tilt Foot Lever

Adjustable Tilt Foot

2.Push up the Adjustable Tilt Foot Levers on the right and left sides of the projector to extend the adjustable tilt feet (maximum height).

3.Push down the Adjustable Tilt Foot Levers.

If no input signal is present, the input will be skipped. When the input source you wish to project is displayed, release the button.

Press the ENTER button.

4.Lower the front of the projector to the desired height (max. 44.5mm/ 1.8”) and release the Adjustable Tilt Foot Lever to lock the Adjustable tilt foot. There is approximately 10 degrees of up and down adjust- ment for the front of the projector.

WARNING: To avoid premature lamp failure, do not tilt the front of the projector up or down by more than 15° from level.

E-19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Models 8805 Safety Cautions Lamp Replacement Fire and Shock PrecautionsWhats in the Box? Table of Contents Introduction Features youll enjoyIntroduction to the Projector Attaching the lens cap Part Names of the ProjectorCarrying the Projector Select Top FeaturesTerminal Panel Features On the screen using the Select Part Names of the Remote ControlSelect Using the Remote Control in Wired Operation Battery InstallationRemote Control Precautions Operating Range for Wireless Remote ControlSetting Up the Screen and the Projector Installation and ConnectionsSelecting a Location Wide Tele Connecting Your PC with a DVI Connector When Viewing a DVI Digital SignalConnecting Your PC or Macintosh Computer Connecting to RGB 2 in connectorsCommercially available Female Connecting an External MonitorTo connect Scart output RGB To RGBOptional 15-pin-to-RCA female×3 cable ADP-CV1 Connecting Your DVD PlayerAudio Equipment VCR/ Laser disc player Connecting Your VCR or Laser Disc PlayerConnecting the Supplied Power Cable Video cable not supplied Audio equipmentTurning on the Projector Projecting AN Image Basic OperationPress the Enter button to execute the selection Selecting the computer or video source Adjusting the Picture Size and PositionAdjust the Tilt Foot Selecting a SourceUse the Focus Button +/- to obtain the best focus When using the remote control or cabinet buttonsUsing Auto Focus FocusPress the Enter button Screen Use the Select When using the USB connected to the projectorConfirmation screen is displayed Optimizing RGB Picture Automatically Turning Up or Down VolumeUsing the Laser Pointer Adjusting the Image Using Auto AdjustTurning off the Projector Setting the function switchTo turn off the projector Using the Remote Mouse Function Convenient FeaturesAuto 3D Reform Executing the Auto 3D Reform featureAdjustment Setting Screen of Auto 3D ReformFreezing a Picture Using the PointerGetting the On-line Help Operate the Menus using the USB mouse Using a USB Mouse Using the USB HUB FunctionUsing the middle button on the mouse Pen Eraser Drive Drag Changing Background LogoMaking Freehand Drawings on a Projected Image ChalkBoard USB Memory Device or USB Memory Card Reader SupportMaking the Most out of the Viewer Function Using the ViewerOperating the Viewer Function from the Projector playback When the tool bar is not displayedProjecting slides Viewer Preparations Auto Play ModeSwitching to Slides Directly from Other Input Modes Viewing Digital ImagesDeleting Captured Images Using the PC Card Files Fucntion PC Card FilesBasic Menu Operation Using ON-SCREEN MenuUsing the Menus Default Custom Menu items areAdvanced Menu Menu treeDefault Source Select Operation Mode SelectCommunication Speed WEP Highlight Title bar Tab Check box Drag Tool bar Menu ElementsMenu Descriptions & Functions Entering Alphanumeric Characters by Using the MenuSource Select Image Options Entry Edit CommandPicture not available for Viewer and LAN SoundPicture Management Projector Options Using Adapting Color Correction Wall Color Correction Palette Menu Setup Resolution manually User can adjust the image display functions HoriHttp server functions are not available during Standby mode Selecting Lamp Mode and Lamp Type Lamp Setting Selecting Auto Functions Selecting Aspect Ratio and Position for Screen ScreenNetwork Type required for wireless only Setting LAN ModePared to use of 64bit datalength encryption WEP for Wireless onlyNications may be monitored by someone Uses 64-bit datalength for secure transmissionEntry Setting a PasswordStatus Changing the menu to Advanced Editing the custom menuSecurity To enable Security, use the SelectTo delete PC card data you registered Tools Returning to Factory DefaultHelp Replacing the Lamp MaintenanceTo replace the lamp Reinstall the new filter cover Catch CleaningCleaning or Replacing the Filter Cleaning the Cabinet and the LensLamp Indicator TroubleshootingPower Indicator Status IndicatorImage isn’t square to Common Problems & Solutions Check These ItemsFor more information contact your dealer Page Model Number 8946 Optical SpecificationsModel Number 8805 Optical Pin No RGB Signal Analog YCbCr Signal Cabinet DimensionsPin Assignments of D-Sub RGB Input Connector Mini D-Sub 15 Pin ConnectorUxga 1600×1200 is supported for separate sync signal only Compatible Input Signal ListCable Connection PC Control Connector D-SUB 9PUsing Software Keyboard PC Control Codes and Cable ConnectionHandling of the Address for Operation via a Browser Operation Using an Http BrowserOverview Preparation Before UsePage Page Orders 676-2485 Phone 762-4040401-8805/8946-00
Top Page Image Contents