Dukane 8946 To enable Security, use the Select, To delete PC card data you registered

Page 53

Security

The Security function enables you to protect your projector so that the projector will not project a signal unless you enter a keyword. There is also an option to lock the projector by using a registered PC card as a protect key. Once you have registered your PC card as a protect key, you are required to insert the registered PC card into the PC card slot of the projector each time you turn on the projector. You can enable the Security function by using a keyword only.

Enable/Disable

This turns the Security function on or off.

Keyword

Enter an appropriate keyword when you use

 

the Security function.

 

(Up to 10 characters can be used.)

 

The Security function is available only when

 

your keyword is entered.

Use Protect key

Check this box to lock your projector when

 

using a PC card. To use a keyword without

 

a PC card, do not check this box.

Drive

Switches between PC Card slot 1 and 2.

Read

Reads data of a PC card.

Register

Registers data of the PC card.

 

The Security function is not available unless

 

at least one PC card is registered. (if the

 

“Use Protect key” check box is selected)

 

Up to 5 PC cards can be registered.

Delete

Deletes data of a registered PC card.

To set up a keyword to enable the Security function without using a registered PC card.

1. Use the SELECT button to select “Keyword” and use the soft- ware keyboard to enter a keyword.

NOTE: Please make a note of your keyword.

2.

Use the SELECT

button to select “Enable” and use the SELECT

 

button to select “OK”, then the Security function will be enabled.

 

An “Are you sure?” message will appear. Use the SELECT

but-

 

ton and press the ENTER button.

 

 

The Security function takes effect.

 

To register a PC card as a protect key.

 

1.

Insert a PC card into the PC card slot of the projector.

 

2.

Use the SELECT

button to select "Use Protect Key" and press

 

the ENTER button.

 

 

3.

Use the SELECT

button to select "Read" and press the ENTER

 

button.

 

 

 

Data of the PC card will be read into the projector.

 

4.

Use the SELECT

button to select "Register" and press the EN-

 

TER button.

 

 

Downloaded data will be registered and be displayed in the list win- dow.

5. Use the SELECT button to select "Keyword" and use the soft- ware keyboard to enter a keyword.

NOTE: To use a PC card as a protect key, you must also set up a keyword. Please make a note of your keyword.

This completes registration of your PC card.

To enable Security, use the SELECT

button to select "Enable" and

use the SELECT

button to select "OK" and "Security function will

be enabled. An “Are you sure?" message will appear. Use the SELECT button and press the ENTER button.

The Security function takes effect.

To turn on the projector when Security is enabled (when using your keyword only).

1.Press and hold the POWER button for a minimum of two seconds.

The projector will be turned on and display a message to the effect that the projector is security-protected.

2.Select [Projector Options] [Security] from the menu and press the ENTER button.

The Release Code input screen will be displayed.

3.Enter your keyword in the Release Code input screen. You can view the projected image.

NOTE: Do not forget your keyword. However, if you forget your keyword, your dealer will provide you with your Release Code. See more information at the end of this section.

To turn on the projector when Security is enabled (when using a PC card as a protect key).

1.Insert your registered PC card into the PC card slot.

2.Press and hold the POWER button for a minimum of two seconds. The projector will turn on and then recognize the PC card. Once the image has been projected, it will stay on without the PC card.

The security disable mode is maintained until the main power is turned off (by setting the main power switch to "O" or unplugging the power cord).

In the following cases you will be asked to check the protect key or input the keyword:

(1)When "OK" is selected at an image for which security is set and the power is turned off then back on

(2)When the main power is turned off then back on while the secu- rity function is enabled

(3)When you attempt to display an image for which security is set while the security function is enabled

Blanks (spaces) cannot be used in the Keyword section.

To delete PC card data you registered.

1.

Use the SELECT

button to select "Delete" and use the SELECT

 

button to select the list window.

2.

Use the SELECT

button to select the PC card data you wish to

 

delete.

 

3.

Press the SELECT

button to select "Delete" and press the ENTER

 

button.

 

The PC card data will be deleted.

E-53

Image 53
Contents Models 8805 Safety Cautions Whats in the Box? Fire and Shock PrecautionsLamp Replacement Table of Contents Introduction to the Projector Features youll enjoyIntroduction Carrying the Projector Part Names of the ProjectorAttaching the lens cap Select Top FeaturesTerminal Panel Features On the screen using the Select Part Names of the Remote ControlSelect Remote Control Precautions Battery InstallationOperating Range for Wireless Remote Control Using the Remote Control in Wired OperationSelecting a Location Installation and ConnectionsSetting Up the Screen and the Projector Wide Tele Connecting Your PC or Macintosh Computer When Viewing a DVI Digital SignalConnecting to RGB 2 in connectors Connecting Your PC with a DVI ConnectorTo connect Scart output RGB Connecting an External MonitorTo RGB Commercially available FemaleAudio Equipment Connecting Your DVD PlayerOptional 15-pin-to-RCA female×3 cable ADP-CV1 Connecting the Supplied Power Cable Connecting Your VCR or Laser Disc PlayerVideo cable not supplied Audio equipment VCR/ Laser disc playerPress the Enter button to execute the selection Projecting AN Image Basic OperationTurning on the Projector Adjust the Tilt Foot Adjusting the Picture Size and PositionSelecting a Source Selecting the computer or video sourceUsing Auto Focus When using the remote control or cabinet buttonsFocus Use the Focus Button +/- to obtain the best focusConfirmation screen is displayed When using the USB connected to the projectorPress the Enter button Screen Use the Select Using the Laser Pointer Turning Up or Down VolumeAdjusting the Image Using Auto Adjust Optimizing RGB Picture AutomaticallyTo turn off the projector Setting the function switchTurning off the Projector Using the Remote Mouse Function Convenient FeaturesAuto 3D Reform Executing the Auto 3D Reform featureAdjustment Setting Screen of Auto 3D ReformGetting the On-line Help Using the PointerFreezing a Picture Using the middle button on the mouse Using a USB Mouse Using the USB HUB FunctionOperate the Menus using the USB mouse Making Freehand Drawings on a Projected Image ChalkBoard Changing Background LogoUSB Memory Device or USB Memory Card Reader Support Pen Eraser Drive DragMaking the Most out of the Viewer Function Using the ViewerProjecting slides Viewer When the tool bar is not displayedOperating the Viewer Function from the Projector playback Switching to Slides Directly from Other Input Modes Auto Play ModeViewing Digital Images PreparationsDeleting Captured Images Using the PC Card Files Fucntion PC Card FilesUsing the Menus Using ON-SCREEN MenuDefault Custom Menu items are Basic Menu OperationAdvanced Menu Menu treeCommunication Speed Operation Mode SelectDefault Source Select WEP Highlight Title bar Tab Check box Drag Tool bar Menu ElementsSource Select Entering Alphanumeric Characters by Using the MenuMenu Descriptions & Functions Picture not available for Viewer and LAN Entry Edit CommandSound Image OptionsPicture Management Projector Options Using Adapting Color Correction Wall Color Correction Palette Menu Setup Http server functions are not available during Standby mode User can adjust the image display functions HoriResolution manually Selecting Lamp Mode and Lamp Type Lamp Setting Selecting Auto Functions Selecting Aspect Ratio and Position for Screen ScreenNetwork Type required for wireless only Setting LAN ModeNications may be monitored by someone WEP for Wireless onlyUses 64-bit datalength for secure transmission Pared to use of 64bit datalength encryptionStatus Setting a PasswordChanging the menu to Advanced Editing the custom menu EntryTo delete PC card data you registered To enable Security, use the SelectSecurity Help Returning to Factory DefaultTools To replace the lamp MaintenanceReplacing the Lamp Cleaning or Replacing the Filter CleaningCleaning the Cabinet and the Lens Reinstall the new filter cover CatchPower Indicator TroubleshootingStatus Indicator Lamp IndicatorFor more information contact your dealer Common Problems & Solutions Check These ItemsImage isn’t square to Page Model Number 8946 Optical SpecificationsModel Number 8805 Optical Pin Assignments of D-Sub RGB Input Connector Cabinet DimensionsMini D-Sub 15 Pin Connector Pin No RGB Signal Analog YCbCr SignalUxga 1600×1200 is supported for separate sync signal only Compatible Input Signal ListUsing Software Keyboard PC Control Connector D-SUB 9PPC Control Codes and Cable Connection Cable ConnectionOverview Operation Using an Http BrowserPreparation Before Use Handling of the Address for Operation via a BrowserPage Page 401-8805/8946-00 Phone 762-4040Orders 676-2485