Dukane 9015 manual Installing Batteries, Open the back cover, Install the batteries

Page 14

Controls and Features (cont.)

Installing Batteries

Install batteries in the remote control. If the remote control has started to work erratically, replace the batteries.

1 Open the back cover.

While pushing on the back cover, slide it in the direction of the arrow.

2 Install the batteries.

Place the two batteries (AAA/R03-size) supplied in the remote control as illustrated below.

Precautions for using batteries

If batteries are used incorrectly, they may crack or leak liquid. This could cause a fire, burn, malfunction, or staining or damaging the surrounding.

Beware of the following:

•Do not mix new and old batteries.

•Do not mix different types of batteries as they differ in characteristics.

•Place batteries so they match the polarities indicated:

(+) to (+) and (–) to (–).

•Be sure to put the minus (–) end in first to avoid short- circuiting.

•Use only designated batteries.

•Remove the batteries if not used for a prolonged period of time.

•When the batteries are exhausted, replace them immediately. Otherwise, liquid could leak, or malfunction could occur due to leaked liquids. If the leaked liquid contacts the skin, wipe it off with a cloth, otherwise the skin could become rough.

•Do not put batteries into fire or try to recharge them.

•Batteries run for six months to one year in normal use. But the batteries supplied are for confirming operation and may not run that long. When the remote control starts failing to work properly, replace the batteries with new ones.

3 Close the back cover.

Slide the back cover in the direction of the arrow until a click is heard.

14

Image 14

Contents ImagePro Safety Precautions About burning-in of the D-ILA deviceSafety Precautions Lamp directly by opening the cabinet while the illuminationContents Accessories Controls and Features Front Side / Top Surface / Right SideConnector panel AC in power input terminalMain Power switch Adjustable foot for horizontal angle adjustmentOpening for replacing the light-source lamp Bottom SurfaceAir intake area filter Fixing foot Position selecting screw for ceiling mountingControl Panel Video button Setting buttonWhen a menu is shown Computer buttonRS-232C terminal D-sub 9 pin Connector PanelC S video input terminal Mini DIN 4 pin Computer OUT computer output terminal D-sub 3-row 15 pinComputer in computer input -1 terminal D-sub 3- row 15 pin Audio input terminal stereo mini jackProjector’s speakers Audio audio input terminal stereo mini jackRemote Control Unit Precautions for using batteries Installing BatteriesInstall the batteries Open the back coverDo not install the projector in the following places Installing the ProjectorPrecautions for Installation When installing the projector, observe the followingsCenter line of the lens Projection Distance and Screen SizeProjection screen size diagonal length Projection62.32 ft 19.0 m 328 Approx cm 495 55.76 ft 17.0 m 294 Approx cm 44359.04 ft 18.0 m 311 Approx cm 469 65.6 ft 20.0 m 345 Approx cm 521Effective range and distance of the remote control unit Effective Range and Distance of the Remote Control UnitSetting the position selecting screw for Ceiling Mounting Video signals Connecting to Various DevicesSignals that Can Be Input to the Projector Computer signalsVideo devices Connecting to Video DevicesConnecting to Hi-Vision Devices Hi-Vision devicesDesktop type Connecting to Other DevicesConnecting to Devices which Control the Projector To Audio OUTRead the manual which comes with each device thoroughly Connecting to Computer DevicesConnection to an IBM PC or IBM-compatible computer OUTPersonal computer connection cable To monitor connector SuppliedConnection to Macintosh Remove the lens cap Connecting the Power Cord SuppliedTo use the projector To prevent fire and electric shock, observe the followingWhen Turning On the Devices Connected to the Projector Turning off the Power Turning on the PowerTurn on the Main Power switch Basic OperationsWhen you press Computer Adjust the screen sizeWhen you press Video FollowsAdjust focus with the remote control’s Focus +/- buttons Adjust focusAdjust sound volume Projector’s button To turn off video image and audio sound temporarilyTo use the quick alignment function Press onceProjector button Remote control unit To display the Setting menuTo use the remote control’s Preset button To display the Main menuPress the Setting button of the projector Operating the Setting MenuMaking Basic Settings Press the Setting button to select the desired itemOperating the Main Menu Configuration of the Main Menu Computer-related input Operating the Main Menu Basic Operation of the Main Menu Set the color system with the cursor button 2 or Changing the Color SystemSelect Decoder with the cursor button 5 or ∞ To finish the main menu, press the page Back buttonLanguage display Changing the Language DisplaySet the desired language with the cursor button 2 or About language displayButton Adjustment content Adjusting the Pixel ClockAdjust Tracking and Phase with the cursor buttons Select Position with the cursor button 5 or ∞ Adjusting the Screen PositionAdjust H. POS. and V. POS. with the cursor buttons When AV signals are input Adjusting Picture QualitySelect the item to adjust with the cursor button 5 or ∞ When computer-related signals are inputFor computer system input Submenu itemsFor video system input Picture menuNormal TEXT1 TEXT2 Select the Sound with the cursor Adjusting Sound QualityAdjust Treble and Bass with the cursor buttons Button 5 or ∞Following optional functions can be set adjusted Setting and Adjusting Other Functions OptionsSelect the item to set adjust with the cursor button 5 or ∞ Select the Options with the cursor button 5 or ∞Set adjust the desired item with the cursor button 2 or Options menuAspect Input mode Factory setting Changing Setting the SourceSelect the item to set using the cursor buttons 5/∞ or 2/3 Source item shown in text is indicated in magenta colorFix it When Auto is selectedWhen other than Auto is selected Submenu itemReplacing the Light-Source Lamp Loosen the two screws with a flat-end screwdriverHandle Lamp unit Insert the new lamp unit fully inside and fasten the screwsFasten the two screws with a flat-end screwdriver Projector’s button Resetting the Lamp Use TimeTurn on the Main Power switch to go into stand-by mode At the same time for six seconds or moreClean the filter Cleaning and Replacing the FilterTurn off the Main Power switch Reinstall the filterTroubleshooting Maintenance Computer in Computer input SpecificationsAV in AV in input Other Top Outside dimensionsDTV-format signals FrontRS-232C terminal Pin assignment Specifications for terminalsTerminal Computer IN-1 PC / Computer OUT Terminal