Dukane 9015 manual Adjust the screen size, Follows, When you press Video, When you press Computer

Page 27

Basic Operations (Cont.)

■ Projector’s buttons	2. Select the video input to be projected

STAND BY

■Press the VIDEO button or the COMPUTER button to switch the input.

• Each time you press either button, the selected input changes as

OPERATE

follows.

■When you press VIDEO:

LAMP

Y/C VIDEO Y,PB/B-Y,PR/R-Y

TEMP

EMERGENCY

■When you press COMPUTER:

VIDEO	VIDEO button	COMPUTER 1	COMPUTER 2
		COMPUTER 1	COMPUTER 2
COMPUTER	COMPUTER button
SETTING		Remote control unit	Projector
SETTING
+3		COMPUTER VIDEO	VIDEO
QUICK		COMPUTER VIDEO	VIDEO
QUICK
ALIGN.
-2			COMPUTER
		Screen display
		V I D E O	N T S C ( 4 8 0 i )

■Remote control unit

OPERATE	COMPUTER	VIDEO
	T
VOL.	ZOOM	FOCUS
	W
PAGE	MENU/ENTER
PAGE
BACK
PRESET
QUICK		AV
ALIGN.		MUTING

COMPUTER button VIDEO button

ZOOM (T/W) buttons

*When the input is switched, the line display (ex. VIDEO) and the source display (ex. NTSC(480i)) are shown on the upper part of the screen (they disappear in about five seconds). However, they will not be shown if LINE DISPLAY in “Setting and Adjusting Other Functions (OPTIONS)” on page 43 is set to OFF.

(For setting the source, see page 46.)

Note

• To select the proper audio input for video input

The video input terminal (AV IN input terminal) can be switched with the VIDEO button. However, since this projector has only a single audio input terminal, reconnect audio input in accordance with the AV device to be used.

3.Adjust the screen size

■Adjust the screen size with the remote control’s ZOOM (T/W) buttons.

■To enlarge the screen size: Press the ZOOM (W) button.

■To reduce the screen size: Press the ZOOM (T) button.

Remote control unit

ENGLISH

ATTENTIONS

•DO NOT give any shock to this projector while operating it; otherwise, the light-source lamp goes off (the EMERGENCY indicator lights up).

If the shock turns off the light-source lamp —

Turn off the power by pressing the MAIN POWER switch, then turn it on again. Now you can operate the projector as usual.

T

ZOOM

W

Note

•The adjustment of the screen size (zoom adjustment) can also be made on the setting menu.

For operating the setting menu, refer to “Making Basic Settings” on page 31.

27

Image 27

Contents ImagePro About burning-in of the D-ILA device Safety PrecautionsLamp directly by opening the cabinet while the illumination Safety PrecautionsContents Accessories Front Side / Top Surface / Right Side Controls and FeaturesAdjustable foot for horizontal angle adjustment AC in power input terminalMain Power switch Connector panelFixing foot Position selecting screw for ceiling mounting Bottom SurfaceAir intake area filter Opening for replacing the light-source lampControl Panel Computer button Setting buttonWhen a menu is shown Video buttonComputer OUT computer output terminal D-sub 3-row 15 pin Connector PanelC S video input terminal Mini DIN 4 pin RS-232C terminal D-sub 9 pinAudio audio input terminal stereo mini jack Audio input terminal stereo mini jackProjector’s speakers Computer in computer input -1 terminal D-sub 3- row 15 pinRemote Control Unit Open the back cover Installing BatteriesInstall the batteries Precautions for using batteriesWhen installing the projector, observe the followings Installing the ProjectorPrecautions for Installation Do not install the projector in the following placesProjection Projection Distance and Screen SizeProjection screen size diagonal length Center line of the lens65.6 ft 20.0 m 345 Approx cm 521 55.76 ft 17.0 m 294 Approx cm 44359.04 ft 18.0 m 311 Approx cm 469 62.32 ft 19.0 m 328 Approx cm 495Effective Range and Distance of the Remote Control Unit Setting the position selecting screw for Ceiling MountingEffective range and distance of the remote control unit Computer signals Connecting to Various DevicesSignals that Can Be Input to the Projector Video signalsHi-Vision devices Connecting to Video DevicesConnecting to Hi-Vision Devices Video devicesTo Audio OUT Connecting to Other DevicesConnecting to Devices which Control the Projector Desktop typeOUT Connecting to Computer DevicesConnection to an IBM PC or IBM-compatible computer Read the manual which comes with each device thoroughlyTo monitor connector Supplied Connection to MacintoshPersonal computer connection cable To prevent fire and electric shock, observe the following Connecting the Power Cord SuppliedTo use the projector Remove the lens capWhen Turning On the Devices Connected to the Projector Basic Operations Turning on the PowerTurn on the Main Power switch Turning off the PowerFollows Adjust the screen sizeWhen you press Video When you press ComputerAdjust focus Adjust sound volumeAdjust focus with the remote control’s Focus +/- buttons Press once To turn off video image and audio sound temporarilyTo use the quick alignment function Projector’s buttonTo display the Main menu Remote control unit To display the Setting menuTo use the remote control’s Preset button Projector buttonPress the Setting button to select the desired item Operating the Setting MenuMaking Basic Settings Press the Setting button of the projectorOperating the Main Menu Configuration of the Main Menu Computer-related input Operating the Main Menu Basic Operation of the Main Menu To finish the main menu, press the page Back button Changing the Color SystemSelect Decoder with the cursor button 5 or ∞ Set the color system with the cursor button 2 orAbout language display Changing the Language DisplaySet the desired language with the cursor button 2 or Language displayAdjusting the Pixel Clock Adjust Tracking and Phase with the cursor buttonsButton Adjustment content Adjusting the Screen Position Adjust H. POS. and V. POS. with the cursor buttonsSelect Position with the cursor button 5 or ∞ When computer-related signals are input Adjusting Picture QualitySelect the item to adjust with the cursor button 5 or ∞ When AV signals are inputPicture menu Submenu itemsFor video system input For computer system inputNormal TEXT1 TEXT2 Button 5 or ∞ Adjusting Sound QualityAdjust Treble and Bass with the cursor buttons Select the Sound with the cursorSelect the Options with the cursor button 5 or ∞ Setting and Adjusting Other Functions OptionsSelect the item to set adjust with the cursor button 5 or ∞ Following optional functions can be set adjustedOptions menu Set adjust the desired item with the cursor button 2 orAspect Source item shown in text is indicated in magenta color Changing Setting the SourceSelect the item to set using the cursor buttons 5/∞ or 2/3 Input mode Factory settingSubmenu item When Auto is selectedWhen other than Auto is selected Fix itLoosen the two screws with a flat-end screwdriver Replacing the Light-Source LampInsert the new lamp unit fully inside and fasten the screws Fasten the two screws with a flat-end screwdriverHandle Lamp unit At the same time for six seconds or more Resetting the Lamp Use TimeTurn on the Main Power switch to go into stand-by mode Projector’s buttonReinstall the filter Cleaning and Replacing the FilterTurn off the Main Power switch Clean the filterTroubleshooting Maintenance Specifications AV in AV in inputComputer in Computer input Other Front Outside dimensionsDTV-format signals TopComputer IN-1 PC / Computer OUT Terminal Pin assignment Specifications for terminalsTerminal RS-232C terminal