Dukane 9015 Changing Setting the Source, Source item shown in text is indicated in magenta color

Page 46
• The submenu items, SOURCE menu, appears on the screen.
• The main menu appears on the screen.

Operating the Main Menu (Cont.)

Changing (Setting) the Source

■Remote control unit

Normally, use the source setting in AUTO. If use in AUTO is unstable such as color not appearing, the screen being disturbed or the screen being intermitted, set to the dedicated source (forced mode) in accordance with the input signal.

MENU/ENTER

OPERATE

button

COMPUTER VIDEO

 

T

 

VOL.

ZOOM

FOCUS

 

W

 

PAGE

MENU/ENTER

 

 

BACK

 

 

PRESET

 

 

 

 

Cursor buttons

QUICK

 

AV

ALIGN.

 

MUTING

• When shipped from the factory, the source settings are as follows:

Input mode

Factory setting

 

Input mode

Factory setting

VIDEO

NTSC(480i)

 

COMPUTER 1

AUTO

 

 

 

 

 

Y/C

NTSC(480i)

 

COMPUTER 2

AUTO

 

 

 

 

 

Y, PB/B-Y, PR/R-Y

AUTO

 

—

—

 

 

 

 

 

Notes

•Depending on the signal from a device connected, adjustment may be needed after a dedicated source is set. If that is the case, adjust the appropriate items.

•When the input mode (SOURCE) is VIDEO or Y/C, and if AUTO is set, the automatic detecting function may work, possibly causing the screen to be intermitted or disturbed. In that case, set to a dedicated source (forced mode).

•When special effect playback (fast-forward/ twice-speed/triple-speed) is performed on a video deck, etc, the picture may be disturbed or intermitted, depending on the device.

•When inputting 480p or 720p-DTV-format signal in COMPUTER2 input mode, use the dedicated source mode “SDTV(480p)” or “HDTV1(720p)”. (At AUTO, 480p or 720p signal can not be detected.)

PAGE BACK button

■Main menu

V I D E O

A U T O ( N T S C ( 4 8 0 i ) )

P I X E L C L O C K

P O S I T I O N

P I C T U R E

S O U N D

O P T I O N S

S O U R C E

1 Press the MENU/ENTER button.

2 Select a submenu item “SOURCE” using the cursor button 5 or ∞ .

• The SOURCE item (shown in text) is indicated in magenta color.

3 Press the MENU/ENTER button.

D E C O D E R A U T O ( N T S C ( 4 8 0 i ) )

L A N G U A G E E N G L I S H

Submenu item [SOURCE]

S O U R C E

( A U T O )

A U T O

S V G A 1

N T S C ( 4 8 0 i )

S V G A 2

S D T V ( 4 8 0 p )

M A C 1 6

H D T V 1 ( 7 2 0 p )

X G A 1

H D T V 2 ( 1 0 8 0 i )

X G A 2

P A L / S E C A M

M A C 1 9

P C - 9 8

M A C 2 1

V G A 1

S X G A 1

V G A 3

S X G A 2

M A C 1 3

S X G A 3

V G A V E S A

 

The display in ( ) shows the currently set status.

(SOURCE menu)

Notes

•The selected item is shown in magenta color. Items shown in gray color cannot be operated or set in the current mode.

•Items that can be set are different when video signals are input and when computer signals are input.

•For dedicated source signals (corresponding frequency, etc.) for computer signals, see page 19.

4 Select the item to set using the cursor buttons 5/∞ or 2/3.

• The item to set is shown in magenta color.

S O U R C E

( A U T O )

A U T O

S V G A 1

N T S C

S V G A 2

P A L / S E C A M

M A C 1 6

E D T V I I

X G A 1

H D T V

X G A 2

P C - 9 8

M A C 1 9

V G A 1

M A C 2 1

V G A 3

S X G A 1

M A C 1 3

S X G A 2

V G A V E S A

S X G A 3

(To be continued on the next page)

46

Page 45 Page 47
Image 46
Page 45 Page 47
Contents ImagePro Safety Precautions About burning-in of the D-ILA deviceSafety Precautions Lamp directly by opening the cabinet while the illuminationContents Accessories Controls and Features Front Side / Top Surface / Right SideConnector panel AC in power input terminalMain Power switch Adjustable foot for horizontal angle adjustmentOpening for replacing the light-source lamp Bottom SurfaceAir intake area filter Fixing foot Position selecting screw for ceiling mountingControl Panel Video button Setting buttonWhen a menu is shown Computer buttonRS-232C terminal D-sub 9 pin Connector PanelC S video input terminal Mini DIN 4 pin Computer OUT computer output terminal D-sub 3-row 15 pinComputer in computer input -1 terminal D-sub 3- row 15 pin Audio input terminal stereo mini jackProjector’s speakers Audio audio input terminal stereo mini jackRemote Control Unit Precautions for using batteries Installing BatteriesInstall the batteries Open the back coverDo not install the projector in the following places Installing the ProjectorPrecautions for Installation When installing the projector, observe the followingsCenter line of the lens Projection Distance and Screen SizeProjection screen size diagonal length Projection62.32 ft 19.0 m 328 Approx cm 495 55.76 ft 17.0 m 294 Approx cm 44359.04 ft 18.0 m 311 Approx cm 469 65.6 ft 20.0 m 345 Approx cm 521Setting the position selecting screw for Ceiling Mounting Effective Range and Distance of the Remote Control UnitEffective range and distance of the remote control unit Video signals Connecting to Various DevicesSignals that Can Be Input to the Projector Computer signalsVideo devices Connecting to Video DevicesConnecting to Hi-Vision Devices Hi-Vision devicesDesktop type Connecting to Other DevicesConnecting to Devices which Control the Projector To Audio OUTRead the manual which comes with each device thoroughly Connecting to Computer DevicesConnection to an IBM PC or IBM-compatible computer OUTConnection to Macintosh To monitor connector SuppliedPersonal computer connection cable Remove the lens cap Connecting the Power Cord SuppliedTo use the projector To prevent fire and electric shock, observe the followingWhen Turning On the Devices Connected to the Projector Turning off the Power Turning on the PowerTurn on the Main Power switch Basic OperationsWhen you press Computer Adjust the screen sizeWhen you press Video FollowsAdjust sound volume Adjust focusAdjust focus with the remote control’s Focus +/- buttons Projector’s button To turn off video image and audio sound temporarilyTo use the quick alignment function Press onceProjector button Remote control unit To display the Setting menuTo use the remote control’s Preset button To display the Main menuPress the Setting button of the projector Operating the Setting MenuMaking Basic Settings Press the Setting button to select the desired itemOperating the Main Menu Configuration of the Main Menu Computer-related input Operating the Main Menu Basic Operation of the Main Menu Set the color system with the cursor button 2 or Changing the Color SystemSelect Decoder with the cursor button 5 or ∞ To finish the main menu, press the page Back buttonLanguage display Changing the Language DisplaySet the desired language with the cursor button 2 or About language displayAdjust Tracking and Phase with the cursor buttons Adjusting the Pixel ClockButton Adjustment content Adjust H. POS. and V. POS. with the cursor buttons Adjusting the Screen PositionSelect Position with the cursor button 5 or ∞ When AV signals are input Adjusting Picture QualitySelect the item to adjust with the cursor button 5 or ∞ When computer-related signals are inputFor computer system input Submenu itemsFor video system input Picture menuNormal TEXT1 TEXT2 Select the Sound with the cursor Adjusting Sound QualityAdjust Treble and Bass with the cursor buttons Button 5 or ∞Following optional functions can be set adjusted Setting and Adjusting Other Functions OptionsSelect the item to set adjust with the cursor button 5 or ∞ Select the Options with the cursor button 5 or ∞Set adjust the desired item with the cursor button 2 or Options menuAspect Input mode Factory setting Changing Setting the SourceSelect the item to set using the cursor buttons 5/∞ or 2/3 Source item shown in text is indicated in magenta colorFix it When Auto is selectedWhen other than Auto is selected Submenu itemReplacing the Light-Source Lamp Loosen the two screws with a flat-end screwdriverFasten the two screws with a flat-end screwdriver Insert the new lamp unit fully inside and fasten the screwsHandle Lamp unit Projector’s button Resetting the Lamp Use TimeTurn on the Main Power switch to go into stand-by mode At the same time for six seconds or moreClean the filter Cleaning and Replacing the FilterTurn off the Main Power switch Reinstall the filterTroubleshooting Maintenance AV in AV in input SpecificationsComputer in Computer input Other Top Outside dimensionsDTV-format signals FrontRS-232C terminal Pin assignment Specifications for terminalsTerminal Computer IN-1 PC / Computer OUT Terminal
Top Page Image Contents