Dukane 9015 Cleaning and Replacing the Filter, Turn off the Main Power switch, Remove the filter

Page 51

Cleaning and Replacing the Filter

Clean the filter periodically. If the filter is heavily stained and does not get clean, or if it is damaged, replace the filter with a new filter (part No.: LC30208). Otherwise, dirt may get inside and appear on the screen, possibly preventing you from enjoying the video image fully. If dirt gets inside or if you need information about the filter, consult a JVC- authorized dealer where you have purchased the projector or nearest Dukane Service center.

Turn off the MAIN POWER switch.
1 After the projector goes into stand-by state with the STAND BY indicator on, turn off the main power switch and pull out the
power cord from the projector and the wall outlet.
2 Remove the filter.
	Notes

Loosen the screw with a flat-end screwdriver.	• The screws are fitted so that they do not come off the filter.
	• If the filter is clogged with dirt, etc., the projector goes into an
	emergency mode (the EMERGENCY indicator blinks).
	So, clean the filter periodically. For the emergency mode, refer to
Screw	pages 9 and 25.

Filter

	Be careful not to
	damage the claws.
	Clean the filter.	ENGLISH
	3 Clean the filter with a neutral detergent, wash it in water, and then dry it in the shade.	ENGLISH

4 Reinstall the filter.

Fasten the screw with a flat-end screwdriver.

Notes

•Install the filter correctly. Otherwise, the projector does not operate. (Goes into an emergency mode.)

•If the filter’s claws are damaged, the projector may not operate. Then, replace with a new filter.

CAUTIONS

•Put on rubber gloves when using neutral detergent.

•After you have washed the filter in water, make sure the filter is completely dry before reinstalling it. Otherwise, electric shock or malfunction could occur.

•Do not clean the filter using a vacuum cleaner. Since the filter is soft, it may be sucked into the vacuum cleaner or damaged.

51

Image 51

Contents ImagePro About burning-in of the D-ILA device Safety PrecautionsLamp directly by opening the cabinet while the illumination Safety PrecautionsContents Accessories Front Side / Top Surface / Right Side Controls and FeaturesAdjustable foot for horizontal angle adjustment AC in power input terminalMain Power switch Connector panelFixing foot Position selecting screw for ceiling mounting Bottom SurfaceAir intake area filter Opening for replacing the light-source lampControl Panel Computer button Setting buttonWhen a menu is shown Video buttonComputer OUT computer output terminal D-sub 3-row 15 pin Connector PanelC S video input terminal Mini DIN 4 pin RS-232C terminal D-sub 9 pinAudio audio input terminal stereo mini jack Audio input terminal stereo mini jackProjector’s speakers Computer in computer input -1 terminal D-sub 3- row 15 pinRemote Control Unit Open the back cover Installing BatteriesInstall the batteries Precautions for using batteriesWhen installing the projector, observe the followings Installing the ProjectorPrecautions for Installation Do not install the projector in the following placesProjection Projection Distance and Screen SizeProjection screen size diagonal length Center line of the lens65.6 ft 20.0 m 345 Approx cm 521 55.76 ft 17.0 m 294 Approx cm 44359.04 ft 18.0 m 311 Approx cm 469 62.32 ft 19.0 m 328 Approx cm 495Effective Range and Distance of the Remote Control Unit Setting the position selecting screw for Ceiling MountingEffective range and distance of the remote control unit Computer signals Connecting to Various DevicesSignals that Can Be Input to the Projector Video signalsHi-Vision devices Connecting to Video DevicesConnecting to Hi-Vision Devices Video devicesTo Audio OUT Connecting to Other DevicesConnecting to Devices which Control the Projector Desktop typeOUT Connecting to Computer DevicesConnection to an IBM PC or IBM-compatible computer Read the manual which comes with each device thoroughlyTo monitor connector Supplied Connection to MacintoshPersonal computer connection cable To prevent fire and electric shock, observe the following Connecting the Power Cord SuppliedTo use the projector Remove the lens capWhen Turning On the Devices Connected to the Projector Basic Operations Turning on the PowerTurn on the Main Power switch Turning off the PowerFollows Adjust the screen sizeWhen you press Video When you press ComputerAdjust focus Adjust sound volumeAdjust focus with the remote control’s Focus +/- buttons Press once To turn off video image and audio sound temporarilyTo use the quick alignment function Projector’s buttonTo display the Main menu Remote control unit To display the Setting menuTo use the remote control’s Preset button Projector buttonPress the Setting button to select the desired item Operating the Setting MenuMaking Basic Settings Press the Setting button of the projectorOperating the Main Menu Configuration of the Main Menu Computer-related input Operating the Main Menu Basic Operation of the Main Menu To finish the main menu, press the page Back button Changing the Color SystemSelect Decoder with the cursor button 5 or ∞ Set the color system with the cursor button 2 orAbout language display Changing the Language DisplaySet the desired language with the cursor button 2 or Language displayAdjusting the Pixel Clock Adjust Tracking and Phase with the cursor buttonsButton Adjustment content Adjusting the Screen Position Adjust H. POS. and V. POS. with the cursor buttonsSelect Position with the cursor button 5 or ∞ When computer-related signals are input Adjusting Picture QualitySelect the item to adjust with the cursor button 5 or ∞ When AV signals are inputPicture menu Submenu itemsFor video system input For computer system inputNormal TEXT1 TEXT2 Button 5 or ∞ Adjusting Sound QualityAdjust Treble and Bass with the cursor buttons Select the Sound with the cursorSelect the Options with the cursor button 5 or ∞ Setting and Adjusting Other Functions OptionsSelect the item to set adjust with the cursor button 5 or ∞ Following optional functions can be set adjustedOptions menu Set adjust the desired item with the cursor button 2 orAspect Source item shown in text is indicated in magenta color Changing Setting the SourceSelect the item to set using the cursor buttons 5/∞ or 2/3 Input mode Factory settingSubmenu item When Auto is selectedWhen other than Auto is selected Fix itLoosen the two screws with a flat-end screwdriver Replacing the Light-Source LampInsert the new lamp unit fully inside and fasten the screws Fasten the two screws with a flat-end screwdriverHandle Lamp unit At the same time for six seconds or more Resetting the Lamp Use TimeTurn on the Main Power switch to go into stand-by mode Projector’s buttonReinstall the filter Cleaning and Replacing the FilterTurn off the Main Power switch Clean the filterTroubleshooting Maintenance Specifications AV in AV in inputComputer in Computer input Other Front Outside dimensionsDTV-format signals TopComputer IN-1 PC / Computer OUT Terminal Pin assignment Specifications for terminalsTerminal RS-232C terminal