Dukane 9015 manual Insert the new lamp unit fully inside and fasten the screws, Handle Lamp unit

Page 49

Replacing the Light-Source Lamp (Cont.)

2 Loosen the lamp-unit screws, raise the handle, and pull out the lamp unit.

Loosen the two screws with a flat-end screwdriver.

Note

•The screws are fitted so that they do not come off the lamp- unit.

Screw

Lamp unit

2

1

3 Insert the new lamp unit fully inside and fasten the screws.

Fasten the two screws with a flat-end screwdriver.

CAUTION

•Do not touch the glass surface of the light-source lamp directly with your hand as well as staining it. If you touch with a bare hand, stains on your hand may adhere to the lamp, possibly preventing the lamp from performing as specified due to a shortened lamp life, a darkened screen, etc. To handle a new light-source lamp, hold its plastic part. Never touch the metal part or the front glass surface.

4 Replace the lamp-replacement opening cover and fasten the screws.

Fasten the two screws with a flat-end screwdriver.

Handle

Lamp unit

1

2

Handle	Screw

Lamp-replacement opening cover

Be careful not to damage the claw.

ENGLISH

CAUTIONS

•Install the lamp unit and close the lamp-replacement opening cover correctly; otherwise, a safety switch is activated to prevent the projector from operating.

•If the claw on the lamp-replacement opening cover is damaged, the projector may not possibly operate. Then, replace with a new lamp-replacement opening cover.

•After replacing the lamp, be sure to reset the lamp use time (see page 50).

49

Image 49

Contents ImagePro About burning-in of the D-ILA device Safety PrecautionsLamp directly by opening the cabinet while the illumination Safety PrecautionsContents Accessories Front Side / Top Surface / Right Side Controls and FeaturesMain Power switch AC in power input terminalConnector panel Adjustable foot for horizontal angle adjustmentAir intake area filter Bottom SurfaceOpening for replacing the light-source lamp Fixing foot Position selecting screw for ceiling mountingControl Panel When a menu is shown Setting buttonVideo button Computer buttonC S video input terminal Mini DIN 4 pin Connector PanelRS-232C terminal D-sub 9 pin Computer OUT computer output terminal D-sub 3-row 15 pinProjector’s speakers Audio input terminal stereo mini jackComputer in computer input -1 terminal D-sub 3- row 15 pin Audio audio input terminal stereo mini jackRemote Control Unit Install the batteries Installing BatteriesPrecautions for using batteries Open the back coverPrecautions for Installation Installing the ProjectorDo not install the projector in the following places When installing the projector, observe the followingsProjection screen size diagonal length Projection Distance and Screen SizeCenter line of the lens Projection59.04 ft 18.0 m 311 Approx cm 469 55.76 ft 17.0 m 294 Approx cm 44362.32 ft 19.0 m 328 Approx cm 495 65.6 ft 20.0 m 345 Approx cm 521Setting the position selecting screw for Ceiling Mounting Effective Range and Distance of the Remote Control UnitEffective range and distance of the remote control unit Signals that Can Be Input to the Projector Connecting to Various DevicesVideo signals Computer signalsConnecting to Hi-Vision Devices Connecting to Video DevicesVideo devices Hi-Vision devicesConnecting to Devices which Control the Projector Connecting to Other DevicesDesktop type To Audio OUTConnection to an IBM PC or IBM-compatible computer Connecting to Computer DevicesRead the manual which comes with each device thoroughly OUTConnection to Macintosh To monitor connector SuppliedPersonal computer connection cable To use the projector Connecting the Power Cord SuppliedRemove the lens cap To prevent fire and electric shock, observe the followingWhen Turning On the Devices Connected to the Projector Turn on the Main Power switch Turning on the PowerTurning off the Power Basic OperationsWhen you press Video Adjust the screen sizeWhen you press Computer FollowsAdjust sound volume Adjust focusAdjust focus with the remote control’s Focus +/- buttons To use the quick alignment function To turn off video image and audio sound temporarilyProjector’s button Press onceTo use the remote control’s Preset button Remote control unit To display the Setting menuProjector button To display the Main menuMaking Basic Settings Operating the Setting MenuPress the Setting button of the projector Press the Setting button to select the desired itemOperating the Main Menu Configuration of the Main Menu Computer-related input Operating the Main Menu Basic Operation of the Main Menu Select Decoder with the cursor button 5 or ∞ Changing the Color SystemSet the color system with the cursor button 2 or To finish the main menu, press the page Back buttonSet the desired language with the cursor button 2 or Changing the Language DisplayLanguage display About language displayAdjust Tracking and Phase with the cursor buttons Adjusting the Pixel ClockButton Adjustment content Adjust H. POS. and V. POS. with the cursor buttons Adjusting the Screen PositionSelect Position with the cursor button 5 or ∞ Select the item to adjust with the cursor button 5 or ∞ Adjusting Picture QualityWhen AV signals are input When computer-related signals are inputFor video system input Submenu itemsFor computer system input Picture menuNormal TEXT1 TEXT2 Adjust Treble and Bass with the cursor buttons Adjusting Sound QualitySelect the Sound with the cursor Button 5 or ∞Select the item to set adjust with the cursor button 5 or ∞ Setting and Adjusting Other Functions OptionsFollowing optional functions can be set adjusted Select the Options with the cursor button 5 or ∞Options menu Set adjust the desired item with the cursor button 2 orAspect Select the item to set using the cursor buttons 5/∞ or 2/3 Changing Setting the SourceInput mode Factory setting Source item shown in text is indicated in magenta colorWhen other than Auto is selected When Auto is selectedFix it Submenu itemLoosen the two screws with a flat-end screwdriver Replacing the Light-Source LampFasten the two screws with a flat-end screwdriver Insert the new lamp unit fully inside and fasten the screwsHandle Lamp unit Turn on the Main Power switch to go into stand-by mode Resetting the Lamp Use TimeProjector’s button At the same time for six seconds or moreTurn off the Main Power switch Cleaning and Replacing the FilterClean the filter Reinstall the filterTroubleshooting Maintenance AV in AV in input SpecificationsComputer in Computer input Other DTV-format signals Outside dimensionsTop FrontTerminal Pin assignment Specifications for terminalsRS-232C terminal Computer IN-1 PC / Computer OUT Terminal