Dukane 9015 Replacing the Light-Source Lamp, Loosen the two screws with a flat-end screwdriver

Page 48

Replacing the Light-Source Lamp

The light-source lamp has its service life. It is approximately 1000 hours.

When the light-source lamp approaches the end of its service life, its degradation progresses rapidly. When the lamp’s used hours exceed 900 hours, the projector’s LAMP indicator comes on. Also, at the start of projection (lamp energized), the message “REPL.-LAMP” appears on the projection screen for about two minutes. Then, replace with a new light-source lamp, or arrange for a replacement lamp. When lamp’s service has reached 1000 hours, the projector’s LAMP indicator starts blinking, and if you press the OPERATE button (or press the remote control’s OPERATE button for more than one second), the light-source lamp does not turn on. The specified lamp replacement period is 1000 hours, but depending on use conditions, the replacement period may vary. If video image is dark and its color tint is extraordinary even after you have adjusted color tint and brightness, replace the light-source lamp a little earlier.

Purchase new light-source lamps (part No. : BHL5001-SU) from the Dukane-authorized dealer where you have purchased the projector, or consult the nearest Dukane Service center.

CAUTIONS and NOTES

•If the projector is set up in a tight place which is unsuitable for work, and if you perform replacement work there, this could hurt you. Move the projector to a place wide enough for work, and then replace the lamp.

•Use a genuine product for the light-source lamp. If you use other than a genuine product, this could cause a malfunction. Also, never use an old light-source lamp. An old lamp could cause marked degradation in performance or explode itself, possibly causing the projector to malfunction. Also, its broken pieces could come out of the projector and harm you when replacing the light-source lamp.

•Do not replace the light-source lamp immediately after the projector has been used. The temperature of the light-source lamp is still high and could cause a burn. Be sure to allow a cooling period of one hour or more before performing replacement work.

•Before starting lamp replacement work, turn off the MAIN POWER switch (see page 26), and disconnect the power cord from the wall outlet. If you perform the replacement work with the power cord left connected, this could cause harm or electric shock.

•Never discard an old light-source lamp (used lamp), as is. Otherwise, this could involve a great danger. The lamp contains a xenon gas inside, which is applying a high pressure. If the gas is not removed, it could cause the lamp to explode.

For handling used lamps, refer to the manual supplied with the new replacement lamp you have purchased. If you have any questions, consult a Dukane-authorized dealer where you have bought the replacement lamp or nearest Dukane Service center.

1 Remove the lamp-replacement opening cover by loosening screws.

Loosen the two screws with a flat-end screwdriver.

Screw

Note

• The screws are fitted so that they do not come off the lamp-

replacement opening cover.

Lamp-replacement opening cover

Be careful not to damage the claw.

48

Page 47 Page 49
Image 48
Page 47 Page 49
Contents ImagePro Safety Precautions About burning-in of the D-ILA deviceSafety Precautions Lamp directly by opening the cabinet while the illuminationContents Accessories Controls and Features Front Side / Top Surface / Right SideAC in power input terminal Main Power switchConnector panel Adjustable foot for horizontal angle adjustmentBottom Surface Air intake area filterOpening for replacing the light-source lamp Fixing foot Position selecting screw for ceiling mountingControl Panel Setting button When a menu is shownVideo button Computer buttonConnector Panel C S video input terminal Mini DIN 4 pinRS-232C terminal D-sub 9 pin Computer OUT computer output terminal D-sub 3-row 15 pinAudio input terminal stereo mini jack Projector’s speakersComputer in computer input -1 terminal D-sub 3- row 15 pin Audio audio input terminal stereo mini jackRemote Control Unit Installing Batteries Install the batteriesPrecautions for using batteries Open the back coverInstalling the Projector Precautions for InstallationDo not install the projector in the following places When installing the projector, observe the followingsProjection Distance and Screen Size Projection screen size diagonal lengthCenter line of the lens Projection55.76 ft 17.0 m 294 Approx cm 443 59.04 ft 18.0 m 311 Approx cm 46962.32 ft 19.0 m 328 Approx cm 495 65.6 ft 20.0 m 345 Approx cm 521Effective Range and Distance of the Remote Control Unit Setting the position selecting screw for Ceiling MountingEffective range and distance of the remote control unit Connecting to Various Devices Signals that Can Be Input to the ProjectorVideo signals Computer signalsConnecting to Video Devices Connecting to Hi-Vision DevicesVideo devices Hi-Vision devicesConnecting to Other Devices Connecting to Devices which Control the ProjectorDesktop type To Audio OUTConnecting to Computer Devices Connection to an IBM PC or IBM-compatible computerRead the manual which comes with each device thoroughly OUTTo monitor connector Supplied Connection to MacintoshPersonal computer connection cable Connecting the Power Cord Supplied To use the projectorRemove the lens cap To prevent fire and electric shock, observe the followingWhen Turning On the Devices Connected to the Projector Turning on the Power Turn on the Main Power switchTurning off the Power Basic OperationsAdjust the screen size When you press VideoWhen you press Computer FollowsAdjust focus Adjust sound volumeAdjust focus with the remote control’s Focus +/- buttons To turn off video image and audio sound temporarily To use the quick alignment functionProjector’s button Press onceRemote control unit To display the Setting menu To use the remote control’s Preset buttonProjector button To display the Main menuOperating the Setting Menu Making Basic SettingsPress the Setting button of the projector Press the Setting button to select the desired itemOperating the Main Menu Configuration of the Main Menu Computer-related input Operating the Main Menu Basic Operation of the Main Menu Changing the Color System Select Decoder with the cursor button 5 or ∞Set the color system with the cursor button 2 or To finish the main menu, press the page Back buttonChanging the Language Display Set the desired language with the cursor button 2 orLanguage display About language displayAdjusting the Pixel Clock Adjust Tracking and Phase with the cursor buttonsButton Adjustment content Adjusting the Screen Position Adjust H. POS. and V. POS. with the cursor buttonsSelect Position with the cursor button 5 or ∞ Adjusting Picture Quality Select the item to adjust with the cursor button 5 or ∞When AV signals are input When computer-related signals are inputSubmenu items For video system inputFor computer system input Picture menuNormal TEXT1 TEXT2 Adjusting Sound Quality Adjust Treble and Bass with the cursor buttonsSelect the Sound with the cursor Button 5 or ∞Setting and Adjusting Other Functions Options Select the item to set adjust with the cursor button 5 or ∞Following optional functions can be set adjusted Select the Options with the cursor button 5 or ∞Set adjust the desired item with the cursor button 2 or Options menu Aspect Changing Setting the Source Select the item to set using the cursor buttons 5/∞ or 2/3Input mode Factory setting Source item shown in text is indicated in magenta colorWhen Auto is selected When other than Auto is selectedFix it Submenu itemReplacing the Light-Source Lamp Loosen the two screws with a flat-end screwdriverInsert the new lamp unit fully inside and fasten the screws Fasten the two screws with a flat-end screwdriverHandle Lamp unit Resetting the Lamp Use Time Turn on the Main Power switch to go into stand-by modeProjector’s button At the same time for six seconds or moreCleaning and Replacing the Filter Turn off the Main Power switchClean the filter Reinstall the filterTroubleshooting Maintenance Specifications AV in AV in inputComputer in Computer input Other Outside dimensions DTV-format signalsTop FrontPin assignment Specifications for terminals TerminalRS-232C terminal Computer IN-1 PC / Computer OUT Terminal
Top Page Image Contents