Dukane 9015 manual Controls and Features, Front Side / Top Surface / Right Side

Page 6

Controls and Features

Front Side / Top Surface / Right Side

	1
	-
	+
9	2
	2
8
7
6 5 4	3
1 Control panel	4 Adjustable foot (for adjusting upper/lower angles)

For details, refer to “Control Panel” (page 9).

2Exhaust vents

Vents for cooling fans through which warm air comes out.

CAUTION

•Do not block the exhaust vents, or heat builds up inside, possibly causing a fire. Also, do not touch the vents, or this could cause a low-temperature burn.

3Carrying handle

Raise this handle when carrying the projector.

It is adjusted to be level when shipped from the factory. Turning to extend the foot allows adjustment up to + 7°.

			+7˚
MAIN	AC IN	~
POWER	AC IN
ON
OFF
		Extend	Shorten

How to use the carrying handle

Carrying handle

CAUTIONS

•When carrying the projector, do not give a shock to it. Be careful to keep its balance.

•Do not carry it while the light source lamp is on or the cooling fan is operating. This could cause personal injury.

5Built-in speaker (left)

6Built-in speaker (right)

7Lens

Projection lens, which is an electrically driven, approx. 1.5 x zoom lens. Before projection, remove the lens cap.

8Lens cap

The cap has a string attached and the string is fixed to the projector when shipped from the factory. It is recommended that the cap be fitted on to prevent the lens becoming dirty when the projector is not used.

9Remote sensor

When operating with the remote control, aim it toward this sensor. You can also operate the remote control by pointing it to a screen and allowing the remote sensor to receive the reflected light.

6

Image 6

Contents ImagePro Safety Precautions About burning-in of the D-ILA deviceSafety Precautions Lamp directly by opening the cabinet while the illuminationContents Accessories Controls and Features Front Side / Top Surface / Right SideConnector panel AC in power input terminalMain Power switch Adjustable foot for horizontal angle adjustmentOpening for replacing the light-source lamp Bottom SurfaceAir intake area filter Fixing foot Position selecting screw for ceiling mountingControl Panel Video button Setting buttonWhen a menu is shown Computer buttonRS-232C terminal D-sub 9 pin Connector PanelC S video input terminal Mini DIN 4 pin Computer OUT computer output terminal D-sub 3-row 15 pinComputer in computer input -1 terminal D-sub 3- row 15 pin Audio input terminal stereo mini jackProjector’s speakers Audio audio input terminal stereo mini jackRemote Control Unit Precautions for using batteries Installing BatteriesInstall the batteries Open the back coverDo not install the projector in the following places Installing the ProjectorPrecautions for Installation When installing the projector, observe the followingsCenter line of the lens Projection Distance and Screen SizeProjection screen size diagonal length Projection62.32 ft 19.0 m 328 Approx cm 495 55.76 ft 17.0 m 294 Approx cm 44359.04 ft 18.0 m 311 Approx cm 469 65.6 ft 20.0 m 345 Approx cm 521Effective Range and Distance of the Remote Control Unit Setting the position selecting screw for Ceiling MountingEffective range and distance of the remote control unit Video signals Connecting to Various DevicesSignals that Can Be Input to the Projector Computer signalsVideo devices Connecting to Video DevicesConnecting to Hi-Vision Devices Hi-Vision devicesDesktop type Connecting to Other DevicesConnecting to Devices which Control the Projector To Audio OUTRead the manual which comes with each device thoroughly Connecting to Computer DevicesConnection to an IBM PC or IBM-compatible computer OUTTo monitor connector Supplied Connection to MacintoshPersonal computer connection cable Remove the lens cap Connecting the Power Cord SuppliedTo use the projector To prevent fire and electric shock, observe the followingWhen Turning On the Devices Connected to the Projector Turning off the Power Turning on the PowerTurn on the Main Power switch Basic OperationsWhen you press Computer Adjust the screen sizeWhen you press Video FollowsAdjust focus Adjust sound volumeAdjust focus with the remote control’s Focus +/- buttons Projector’s button To turn off video image and audio sound temporarilyTo use the quick alignment function Press onceProjector button Remote control unit To display the Setting menuTo use the remote control’s Preset button To display the Main menuPress the Setting button of the projector Operating the Setting MenuMaking Basic Settings Press the Setting button to select the desired itemOperating the Main Menu Configuration of the Main Menu Computer-related input Operating the Main Menu Basic Operation of the Main Menu Set the color system with the cursor button 2 or Changing the Color SystemSelect Decoder with the cursor button 5 or ∞ To finish the main menu, press the page Back buttonLanguage display Changing the Language DisplaySet the desired language with the cursor button 2 or About language displayAdjusting the Pixel Clock Adjust Tracking and Phase with the cursor buttonsButton Adjustment content Adjusting the Screen Position Adjust H. POS. and V. POS. with the cursor buttonsSelect Position with the cursor button 5 or ∞ When AV signals are input Adjusting Picture QualitySelect the item to adjust with the cursor button 5 or ∞ When computer-related signals are inputFor computer system input Submenu itemsFor video system input Picture menuNormal TEXT1 TEXT2 Select the Sound with the cursor Adjusting Sound QualityAdjust Treble and Bass with the cursor buttons Button 5 or ∞Following optional functions can be set adjusted Setting and Adjusting Other Functions OptionsSelect the item to set adjust with the cursor button 5 or ∞ Select the Options with the cursor button 5 or ∞Set adjust the desired item with the cursor button 2 or Options menuAspect Input mode Factory setting Changing Setting the SourceSelect the item to set using the cursor buttons 5/∞ or 2/3 Source item shown in text is indicated in magenta colorFix it When Auto is selectedWhen other than Auto is selected Submenu itemReplacing the Light-Source Lamp Loosen the two screws with a flat-end screwdriverInsert the new lamp unit fully inside and fasten the screws Fasten the two screws with a flat-end screwdriverHandle Lamp unit Projector’s button Resetting the Lamp Use TimeTurn on the Main Power switch to go into stand-by mode At the same time for six seconds or moreClean the filter Cleaning and Replacing the FilterTurn off the Main Power switch Reinstall the filterTroubleshooting Maintenance Specifications AV in AV in inputComputer in Computer input Other Top Outside dimensionsDTV-format signals FrontRS-232C terminal Pin assignment Specifications for terminalsTerminal Computer IN-1 PC / Computer OUT Terminal