Dukane 8110H user manual Resetting all settings

Page 61

 

Troubleshooting

Shutting the projector down

Shutdown switch

Only when the projector can not be turned off by usual procedure (14), please push the shutdown switch using a pin or similar, and disconnect the power plug from the power outlet. Before turning it on again, wait at least 10 minutes to make the projector cool down enough.

Resetting all settings

When it is hard to correct some wrong settings, the FACTORY RESET function of SERVICE item in OPTION menu (46) can reset all settings(except LANGUAGE, FILTER TIME, LAMP TIME, FILTER MESSAGE and SECURITY settings and etc.) to the factory default.

Phenomena that may be easy to be mistaken for machine defects

About the phenomenon confused with a machine defect, check and cope with it according to the following table.

Phenomenon

Cases not involving a machine defect

Reference

page

 

 

 

 

 

 

The electrical power cord is not plugged in.

11

 

Correctly connect the power cord.

 

 

 

The main power source has been interrupted during

 

 

operation such as by a power outage (blackout), etc.

11, 14

 

Please disconnect the power plug from the power outlet,

Power does not

and allow the projector to cool down at least 10 minutes,

 

then turn the power on again.

 

come on.

 

 

Either there is no lamp and/or lamp cover, or either

 

 

 

 

of these has not been properly fixed.

 

 

Please turn the power off and disconnect the power plug from

53, 54

 

the power outlet, and allow the projector to cool down at least

 

45 minutes. After the projector has sufficiently cooled down,

 

 

please make confirmation of the attachment state of the lamp

 

 

and lamp cover, and then turn the power on again.

 

 

The signal cables are not correctly connected.

9

 

Correctly connect the connection cables.

 

 

 

Signal source does not correctly work.

–

 

Correctly set up the signal source device by referring to the

 

manual of the source device.

 

Neither sounds

The input changeover settings are mismatched.

15, 16

nor pictures are

Select the input signal, and correct the settings.

outputted.

 

 

The BLANK function for pictures and the MUTE

 

 

 

 

function for sounds are working.

 

 

AV MUTE may be active.

15, 21,

 

Refer to the item “Sound does not come out” and “No

44

 

pictures are displayed” on the next page to turn off the

 

 

MUTE and BLANK functions.

 

(Continued on next page)

61

Page 60 Page 62
Image 61
Page 60 Page 62
Contents Thank you for purchasing this projector About this manualTrademark acknowledgment Contents Fastening the lens cover Checking the contents of packageProjector Part namesRear panel &9 Control panelSTANDBY/ON button &14 Control portComputer button &16 Remote controlArrangement Setting upOn a horizontal surface Suspended from the ceiling Arrangement Monitor Connecting your devicesSpeakers VCR/DVD playerAbout Plug-and-Play capability Connecting your devicesUsing the security bar and slot Connecting power supplyInstalling the batteries Remote controlAbout the remote control signal Changing the frequency of remote control signal Turning on the power Power on/offTurning off the power STANDBY/ON button Power indicatorSelecting an input signal Adjusting the volumeOperating Temporarily muting the soundComputer button Press the MY Source / DOC. Camera button onVideo button MY Source For a computer signal Searching an input signal For no signal Selecting an aspect ratioAdjusting the focus Adjusting the projectors elevatorAdjusting the position Using the automatic adjustment feature For a video signal and s-video signal  For a component video signalCorrecting the keystone distortions Using the magnify featureKeystone button Temporarily blanking the screen Temporarily freezing the screenFreeze button Blank buttonReset button Using the menu functionEasy Menu Advanced MenuIndication in OSD On Screen Display Position buttonIndication Meaning Easy Menu Reset ECO ModeMirror Filter TimeBrightness Picture menuContrast GammaColor Color TempTint SharpnessSAVE-1, SAVE-2, SAVE-3, SAVE-4 Image menu For no signalAuto Adjust PhaseSize ExecuteProgressive Input menuVideo NR Color SpaceComputer Video FormatFrame Lock Standard ResolutionInvalid Scan Freq Setup menuMonitor OUT Standby ModeAudio menu VolumeSpeaker Blank Screen menuStart UP Description MyScreen Capturing error has occurred. Please try againMyScreen registration is finished Message MyScreen LockTemplate Source NameDisplay Description Closed CaptionMode ChannelOption menu Power onAuto Search DirectAuto Power OFFLamp Time MY Button FAN Speed ServiceGhost Filter MessageKEY Lock Factory ResetRemote Freq InformationSecurity menu PasswordEnter the Security menu SecurityTurning off the MyScreen Password Turning on the MyScreen PasswordTurning on the PIN Lock PIN LockTurning off the PIN Lock If you have forgotten your PIN CodeTransition Turning on the Transition DetectorDetector Turning off the Transition DetectorTurning on the MY Text Password MY Text PasswordTurning off the MY Text Password Writing MY TextReplacing the lamp MaintenanceType number 456-8110H Replacing the lamp Lamp warning High Voltage High TemperatureType number UX35971 Filter unit Cleaning and replacing the air filterOther care Caring for the cabinet and remote controlInside of the projector Caring for the lensTroubleshooting An improper signal is input There is no input signalRelated messages Message DescriptionRegarding the indicator lamps Cooling fan is not operating It is time to clean the air filterThere is a possibility that the interior portion has Become heatedResetting all settings Color settings are not correctly adjusted Volume is adjusted to an extremely low levelColor Space setting is not suitable Mute function is workingVertical resolution of the input signal is equal to or ECO Mode function is workingMore than the vertical resolution of display area that is Determined by 1.5 x D-ZOOM adjustment valueSpecifications SpecificationsSpecification Specifications
Top Page Image Contents