Compaq HB1004 manual Certification and Compliance, European Union EU Notice, Safety Compliance

Page 42

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

C-1

Appendix C

Certification and Compliance

European Union (EU) Notice

Products with the CE Marking comply with both the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community.

Compliance with these directives implies conformity to the following European Norms (in brackets are the equivalent international standards):

EN55022 (CISPR 22) - Electromagnetic Interference

EN50082-1 (IEC801-2, IEC801-3, IEC801-4) - Electromagnetic Immunity

EN60950 (IEC950) - Product Safety

CAUTION: Do not plug a phone jack connector in the RJ-45 port. This may damage this device. Les raccordeurs ne sont pas utilisé pour le système téléphonique!

Safety Compliance

Wichtige Sicherheitshinweise (Germany)

1.Bitte lesen Sie diese Hinweise sorgfältig durch.

2.Heben Sie diese Anleitung für den späteren Gebrauch auf.

3.Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie keine Flüssigoder Aerosolreiniger. Am besten eignet sich ein angefeuchtetes Tuch zur Reinigung.

4.Die Netzanschluß steckdose soll nähe dem Gerät angebracht und leicht zugänglich sein.

5.Das Gerät ist vor Feuchtigkeit zu schützen.

6.Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen oder Fallen könnte Beschädigungen hervorrufen.

Compaq HB1004 10Base-T Ethernet Hub

Image 42
Contents HB1004 10BASE-T HUB Compaq HB1004 10Base-T Hub User Guide Contents Appendix a Appendix C Features OverviewPackage Contents RJ-45 Ports LED IndicatorsHub Components Serial COM PortUnit LEDs Hub LED Conditions and DescriptionsStatus Description MDI/MDI-X Slide Switch Port LEDsPort LED Conditions and Descriptions Installation Mounting the HubMounting the Hub on a Flat Surface Mounting the Hub in a Rack Connecting the Hub System Making a Connection via an MDI-X PortPowering On the Hub Making a Connection via the MDI/MDI-X Port PortConnecting the Power Cord Diagnostic Tests LED Diagnostic Test FunctionsTest Function/Component Hub and Port LED Indicators State Indication7A Sample Application Using the HB1004 10Base-T Ethernet Hub ApplicationsOut-of-Band Connection Setup and ConfigurationPreparing for Configuration Management Onsite ConnectionModem Connection Starting the Configuration Program In-Band Connection4Setup and Configuration Open box 6Setup and Configuration Compaq HB1004 System Configuration Main MenuMain Menu Common Menu FunctionsMenu Item Description System Configuration Settings Common Menu Key FunctionsFunction 10Setup and Configuration Displaying System InformationChanging System Configuration System Configuration ScreenAssigning Trap Managers InvalidConfiguring Port Parameters Network Performance14Setup and Configuration Downloading System SoftwareResetting the Configuration Reverting Configuration to Factory SettingsSaving a New Configuration Restarting the AgentSpecifications HB1004 10Base-T Ethernet HubNetwork Criteria Management SupportTable B-1 Diagnosing Hub Indicators TroubleshootingDiagnosing Hub Indicators Symptom Cause SolutionPower and Cooling Problems InstallationPort and Cable Assignments Twisted Pair Cable Table B-2 RJ-45 Port Pin AssignmentsPin Using Diagnostic Mode ConfigurationDescription MIB Object Factory Setting Factory SettingsTable B-3 Factory Default Settings DownloadExit European Union EU Notice Safety ComplianceCertification and Compliance Wichtige Sicherheitshinweise Germany2Certification and Compliance Index LED2Index