Compaq 3000 manual Installation and Maintenance

Page 74

Chapter 3. Installation and Maintenance

13.Connect the UPS serial control cable (17-04729-01) from the UPS connector Controller Shelf host 0 I/O module to the like connector on the UPS.

14.Install jumper connector 12-49700-01 to the Controller Shelf UPS connector on the host 1 I/O module.

CAUTION

To prevent possible damage to the equipment, the input voltage level of the UPS must be set to your specific line voltage before proceeding. Refer to the UPS manual and set the input level to your ac power source(s).

15.After the UPS has been set to the correct input voltage level, set the UPS low-battery warning option to five minutes (refer to UPS manual for instruc- tions).

16.This completes the Controller and Device Expansion Shelf cabling proce- dure. Dress and ty-wrap related cable groups, and then refer to the RAID Ar- ray 3000 Getting Started and Command Console Installation and User Guides for information describing how to setup and configure your subsys- tem.

EK–SMCPQ–UG. C01

3–23

Image 74

Contents RAID Array 3000 Controller Shelf Page Japan USA Contents Installation and Maintenance Second Controller OptionFigures Tables Removing the Controller from the ShelfRevision Record About This Guide Associated Documents Associated DocumentsNomenclature Convention RAID Advisory Board Description ConventionsStyle Conventions RAID Array 3000 UsageWho to contact in Asia Pacific Support and Services Who to contact in the AmericasWho to contact in Europe Product Overview Product DescriptionRAID Array 3000 Controller Shelf RAID Array 3000 6-Slot Device Expansion Shelf Optional Controller Shelf Part Numbers and Model Descriptions DS-SWXRA-GH DS-SWXRA-GK DS-SWXRA-GN DS-HSZ22-AAShelf Features Controller Shelf EnclosureController Shelf Major Components Shelf Cabinet Installation Shelf Major ComponentsDevice I/O Module Upper Mounting Tab Device Port Connector Lower Host I/O Module Device I/O Module Blower Status LEDsCTR UPS Controller Shelf Power Supplies Shelf CoolingUninterruptable Power Supply UPS Power SupplyConnecting the RA3000 Controller Shelf to a Host System 6-Slot Device Expansion Shelf OptionalHost System Host System SHR-1318 Host System Specifications Controller Shelf Technical SpecificationsShelf Technical Specifications Controller Shelf Power and Physical Specifications RAID Array Controller Controller OverviewRAID Array 3000 Single Controller Block Diagram Controller Features Bridging the Gap Between the Host and Device Expansion ShelfDisk Drives Controller Reset and LED Indicators LED/Reset Switch InterfaceFlexible RAID Set Configuration Controller Front PanelEfficient Write and Read Algorithms Performance EnhancementsCustom Components Description RAID Levels SupportedRAID Levels Supported RAID Shelf RAID Set RestrictionsRAID 0 Write Diagram of a RAID 1 Write RAID 0+1Diagram of RAID 0+1 Write RAID 0+1 ExampleDiagram of a RAID 4 Write RAID Diagram of a RAID 5 Write Redundant Operation JbodSystem Parameters Failover InitializationMessage Passing Environmental Backup Power ManagementResponse to Various AC Power Conditions Installation and Maintenance Installation GuidelinesInstalling Shelves in the Cabinet Recommended Single Expansion Shelf Installation SHR-1097 SHR-1098 13 12 11 Retma Cabinet Shelf Support Parts List Installing Shelf SupportsShelf Support Mounting Kits and Installation Guides Installing Shelf Supports in a Retma Cabinet Square Hole Installing UPS Brackets Retma Cabinet Shelf SupportsUPS Rack-mount Bracket Mounting Hardware List UPS Rack-mount Bracket Assemblies UPS Bracket Retma and Metric Hole Locations Rear Power and Scsi Cable Connection Procedures Scsi Bus Target Addresses and Termination Installation and Maintenance Controller/ Single Device Expansion Shelf Cabling Diagram 10 AC Power Wiring Diagram RAID Array 3000 Controller Shelf 11 Controller/ Two Device Expansion Shelf Cabling Diagram RAID Array 3000 Controller Shelf Installation and Maintenance 12 Controller/ Three Device Expansion Shelf Cabling Diagram Installation and Maintenance RAID Array 3000 Controller Shelf 13 Controller/ Four Device Expansion Shelf Cabling Diagram RAID Array 3000 Controller Shelf Controller Shelf Status LEDs 14 Shelf Status LEDsController LEDs Replacing Components FRU’s15 Controller Shelf Field Replaceable Units Controller Shelf Field Replaceable UnitsReplacing a Host or Device I/O SBB 16 Replacing the Host I/O SBBReplacing a Power Supply SBB Replacing the RAID Controller 17 Removing the Controller from the ShelfReplacing the UPS Replacing a Blower18 Replacing a Blower Assembly Replacing the Controller Memory Cache Modules 19 Controller Cache Modules 21 Remove Installed Simm Modules 22 Install Replacement Modules Second Controller Option IntroductionInstalling the Upgrade Save Existing ConfigurationSaving the Existing Configuration Update Firmware Saved ConfigurationUpdate Firmware Using Serial Interface Shutdown RA3000 Install Two SIMMs into Second Controller Insert Module into Simm ConnectorReplace Existing Controller Remove Controller from Top SlotRestore Configuration Restoring Configuration to New ControllerUpdate Firmware on Second Controller Install Original ControllerConfiguring the RA3000 for the Active Mode of Operation Configuring the Dual Controllers Connecting to Your Dual Controller Storage System Verifying the Controller Operating ParametersRAID Array 3000 Storage Subsystem

Related manuals

Manual 137 pages 52.02 Kb