BOXLIGHT CP-324i Operating the computer screen, USB mouse and keyboard control, Move pointer

Page 21

Operating

Operating the computer screen

CAUTION ►Mistaken use of the mouse/keyboard control could damage your equipment.

•While using this function, please connect only with a computer.

•Before connecting, read the manuals of the computer you will connect.

NOTE • It may not be possible to control notebook PC, and other computers with built-in pointing device (e.g. track ball), using this remote control. In this case, before connecting go into BIOS (system setup) and select external mouse, and disable the pointing device. In addition, the mouse may not function if the computer does not have the needed utility program. See your computer’s hardware manual for details.

•The USB control can be used with Windows 95 OSR 2.1 or higher. It may not be possible to use the remote control, depending on the computer’s conﬁgurations and mouse drivers.

•The USB control can be used only for the functions listed below. You cannot do things like press two buttons at once (for instance, pressing two buttons at the same time to move the mouse pointer diagonally).

•This function is not available while the lamp is warming up (the POWER indicator ﬂashes green), and while adjusting the volume and display, correcting for trapezoidal distortion, zooming in on the screen, using the BLANK function, or displaying the menu screen.

USB mouse and keyboard control

1. Connect the projector’s USB port to the computer via the mouse cable.

Available function	Remote control operation

Move pointer	Use ▲, ▼, ◄, ► buttons
Left click with mouse	Press ENTER button
Right click with mouse	Press RESET button
Press keyboard’s HOME key	Press HOME button
Press keyboard’s END key	Press END button
Press keyboard’s PAGE UP key	Press PAGE UP button
Press keyboard’s PAGE DOWN key	Press PAGE DOWN button
Press keyboard’s ESC key	Press ESC button

ENGLISH

21

Image 21

Contents About this manual Thank you for purchasing this projectorTrademark acknowledgment Contents Projector features About contents of packagePreparations CB/PB CR/PR ProjectorControl buttons Remote controlSetting up At 43 screen ArrangementAt 169 screen 169 DownElevator feet Elevator button Adjusting the projectors elevatorFilter cover’s knob About the ﬁlter cover for bottom-up useFilter cover To remove Filter cover for bottom-up useAbout Plug-and-Play capability Connecting your devicesConnecting to a monitor output Connecting to a speaker with ampliﬁer outputExamples of connection with a computer Examples of connection with a VCR/DVD player CR/PRCB/PB AC inlet Connector of the power cord Connecting power supplyPutting batteries Remote controlApprox meters 30º 30º Using the remote controlTurning on the power Power on/offTurning off the power PowerSelecting an input signal Adjusting the volumeOperating Temporarily muting the soundAdjusting the zoom and focus Searching an input signal At a RGB signal Normal  43   At a video signal /no signal 43  169  SmallAdjusting the position Using the automatic adjustment feature At a RGB signal  At a video signalUsing the magnify feature Freezing the screenTemporarily blanking the screen Operating the computer screen Available function Remote control operationUSB mouse and keyboard control Move pointerUsing the menu function Multifunctional settingsEasy Menu Easy Menu Gamma Picture MenuHigh  Middle  LOW  Custom Picture MenuColor Temp SecamProgressive TV  Film  Turn OFFLOAD1  LOAD2  LOAD3  LOAD4 SAVE4 SAVE3  SAVE2  SAVE1Image Menu PhaseOver Scan PositionAt a video signal Auto AdjustImage Menu SizeComponent  Scart RGB Input MenuAuto  Ntsc  PAL  Secam Video FormatInformation Input MenuVolume Setup MenuNormal  Whisper Normal  Hinvert  Vinvert  H&VINVERTMenu Position Screen MenuOSD Bright BlankStart UP Screen MenuMy Screen My Screen LockAuto in Progress while automatically adjusting Using the buttons / turns on/off the message functionMessage No Input is Detected Sync is OUT of RangeOption Menu Reset  CancelSearch Auto OFFFactory Reset Service GhostOption Menu FAN SpeedLamp MaintenanceLamp Case of replacement by yourselfClaws Tabs Center point of claws ClawsAir ﬁlter Apply a vacuum cleaner to the air ﬁlter and ﬁlter coverEnglish There is no input signal Internal portion temperature is risingRelated messages Message Description Related messagesRegarding the indicator lamps It is time to clean the air ﬁlter Regarding the indicator lampsCooling fan is not operating There is a possibility that the interior portionPower switch is not set to the on position Electrical power cord is not pluggedPhenomena that may easily be mistaken for machine defects These has not been properly ﬁxedPhenomena that may easily be mistaken for machine defects RGB input Video input SpeciﬁcationRGB output Communication portSpeciﬁcations