BOXLIGHT CP-324i user manual Related messages, There is no input signal

Page 42

Troubleshooting

Troubleshooting

Related messages

When the unit's power is on, messages such as those shown below may be displayed. When any such message is displayed on the screen, please respond as described below. If the same message is displayed after the treatment, or if a message other than the following appears, please contact your dealer or service company.

Although these messages will be automatically disappeared around several minutes, it will be reappeared every time the power is turned on.

Message

Description

CHANGE THE LAMP

The time the lamp timer has counted is approaching

2000 hours.

 

AFTER REPLACING LAMP,

Preparation of a new lamp, and an early lamp change is

recommended. After you have change the lamp, please be

RESET THE LAMP TIMER.

sure to reset the lamp timer (36).

 

CHANGE THE LAMP

The time the lamp timer has counted is approaching

 

2000 hours, so a lamp change within ** hours is

AFTER REPLACING LAMP,

recommended.

RESET THE LAMP TIMER.

When lamp usage reaches 2000 hours, the power will

THE POWER WILL TURN OFF

automatically be turned off. Please change the lamp by

referring to the section “Lamp”. After you have changed the

AFTER ** hr.

lamp, please be sure to reset the lamp timer (36).

CHANGE THE LAMP

As the time the lamp timer has counted has reached

AFTER REPLACING LAMP,

2000 hours, the power will soon be automatically

turned off.

RESET THE LAMP TIMER.

Please immediately turn the power off, and change the lamp

 

THE POWER WILL TURN OFF

by referring to the section “Lamp”. After changing the lamp,

AFTER 0 hr.

please be sure to reset the lamp timer (36).

NO INPUT IS DETECTED

There is no input signal.

Please confirm the signal input connection, and the status

ON ***

of the signal source.

 

SYNC IS OUT OF RANGE

The horizontal or vertical wavelength of the inputted

signal is outside of the response parameters of this unit.

ON *** fH *****kHz fV *****Hz

 

Please confirm the specs for this unit or the signal source specs.

 

The internal portion temperature is rising.

 

Please turn the power OFF, and allow the unit to cool down at least 20 minutes.

 

After having confirmed the following items, please turn the power ON again.

CHECK THE AIR FLOW

• Is there blockage of the air passage aperture?

• Is the air filter dirty?

 

 

• Does the peripheral temperature exceed 35°C?

 

• If the same indication is displayed after the treatment, please set the

 

HIGH at the FAN SPEED of the item SERVICE of the OPTION menu.

42

Page 41 Page 43
Image 42
Page 41 Page 43
Contents About this manual Thank you for purchasing this projectorTrademark acknowledgment Contents Projector features About contents of packagePreparations Projector CB/PB CR/PRRemote control Control buttonsSetting up At 169 screen ArrangementAt 43 screen 169 DownAdjusting the projectors elevator Elevator feet Elevator buttonFilter cover To remove About the filter cover for bottom-up useFilter cover’s knob Filter cover for bottom-up useConnecting your devices About Plug-and-Play capabilityConnecting to a monitor output Connecting to a speaker with amplifier outputExamples of connection with a computer Examples of connection with a VCR/DVD player CR/PRCB/PB Connecting power supply AC inlet Connector of the power cordRemote control Putting batteriesUsing the remote control Approx meters 30º 30ºTurning off the power Power on/offTurning on the power PowerOperating Adjusting the volumeSelecting an input signal Temporarily muting the sound At a RGB signal Normal  43  Searching an input signalAdjusting the zoom and focus  At a video signal /no signal 43  169  Small At a RGB signal Using the automatic adjustment featureAdjusting the position  At a video signalUsing the magnify feature Freezing the screenTemporarily blanking the screen USB mouse and keyboard control Available function Remote control operationOperating the computer screen Move pointerMultifunctional settings Using the menu functionEasy Menu Easy Menu Picture Menu GammaColor Temp Picture MenuHigh  Middle  LOW  Custom SecamLOAD1  LOAD2  LOAD3  LOAD4 TV  Film  Turn OFFProgressive SAVE4 SAVE3  SAVE2  SAVE1Over Scan PhaseImage Menu PositionImage Menu Auto AdjustAt a video signal SizeAuto  Ntsc  PAL  Secam Input MenuComponent  Scart RGB Video FormatInput Menu InformationNormal  Whisper Setup MenuVolume Normal  Hinvert  Vinvert  H&VINVERTOSD Bright Screen MenuMenu Position BlankMy Screen Screen MenuStart UP My Screen LockMessage Using the buttons / turns on/off the message functionAuto in Progress while automatically adjusting No Input is Detected Sync is OUT of RangeSearch Reset  CancelOption Menu Auto OFFOption Menu Service GhostFactory Reset FAN SpeedMaintenance LampClaws Case of replacement by yourselfLamp Tabs Center point of claws ClawsApply a vacuum cleaner to the air filter and filter cover Air filterEnglish There is no input signal Internal portion temperature is risingRelated messages Related messages Message DescriptionRegarding the indicator lamps Cooling fan is not operating Regarding the indicator lampsIt is time to clean the air filter There is a possibility that the interior portionPhenomena that may easily be mistaken for machine defects Electrical power cord is not pluggedPower switch is not set to the on position These has not been properly fixedPhenomena that may easily be mistaken for machine defects RGB output SpecificationRGB input Video input Communication portSpecifications
Top Page Image Contents