BOXLIGHT CP-324i user manual Phenomena that may easily be mistaken for machine defects

Page 46

Troubleshooting

Phenomena that may easily be mistaken for machine defects

WARNING ►Never use the projector if abnormal operations such as smoke, strange odor, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc. should occur. In such cases, immediately turn off the power switch and then disconnect the power plug from the power outlet After making sure that the smoke or odor has stopped, contact your dealer or service company.

1. Before requesting repair, please check in accordance with the following chart. This operation sometimes resolves your problem.

If the situation cannot be corrected,

2. The projector’s microprocessor may need to be reset. Please push the Restart switch by using a cocktail stick or similar and the projector will restart.

3. Some setting may be wrong. Please use the FACTORY RESET function of SERVICE menu in the OPTION menu (37) to reset all settings to factory

default.

Then, if the problem is not removed after maintenance, please contact your dealer or service company.

Phenomenon

Cases not involving a machine defect

Reference

page

Power does not

come on.

The electrical power cord is not plugged in.

13

Correctly connect the power cord.

 

The power switch is not set to the on position.

16

Set the power switch to [ ] (On).

 

The main power source has been interrupted during

 

operation such as by a power outage (blackout), etc.

 

Please turn the power off, and allow the unit to cool down at

16

least 20 minutes. After the projector has sufficiently cooled

 

down, please turn the power on again.

 

Either there is no lamp and/or lamp cover, or either

 

of these has not been properly fixed.

 

Please turn the power off, and allow the unit to cool down at

38, 39

least 45 minutes. After the projector has sufficiently cooled

 

down, please make confirmation of the attachment state of

 

the lamp and lamp cover, and then turn the power on again.

 

46

Page 45 Page 47
Image 46
Page 45 Page 47
Contents Thank you for purchasing this projector About this manualTrademark acknowledgment Contents About contents of package Projector featuresPreparations Projector CB/PB CR/PRRemote control Control buttonsSetting up At 169 screen ArrangementAt 43 screen 169 DownAdjusting the projectors elevator Elevator feet Elevator buttonFilter cover To remove About the filter cover for bottom-up useFilter cover’s knob Filter cover for bottom-up useConnecting your devices About Plug-and-Play capabilityConnecting to a speaker with amplifier output Connecting to a monitor outputExamples of connection with a computer CR/PR Examples of connection with a VCR/DVD playerCB/PB Connecting power supply AC inlet Connector of the power cordRemote control Putting batteriesUsing the remote control Approx meters 30º 30ºTurning off the power Power on/offTurning on the power PowerOperating Adjusting the volumeSelecting an input signal Temporarily muting the sound At a RGB signal Normal  43  Searching an input signalAdjusting the zoom and focus  At a video signal /no signal 43  169  Small At a RGB signal Using the automatic adjustment featureAdjusting the position  At a video signalFreezing the screen Using the magnify featureTemporarily blanking the screen USB mouse and keyboard control Available function Remote control operationOperating the computer screen Move pointerMultifunctional settings Using the menu functionEasy Menu Easy Menu Picture Menu GammaColor Temp Picture MenuHigh  Middle  LOW  Custom SecamLOAD1  LOAD2  LOAD3  LOAD4 TV  Film  Turn OFFProgressive SAVE4 SAVE3  SAVE2  SAVE1Over Scan PhaseImage Menu PositionImage Menu Auto AdjustAt a video signal SizeAuto  Ntsc  PAL  Secam Input MenuComponent  Scart RGB Video FormatInput Menu InformationNormal  Whisper Setup MenuVolume Normal  Hinvert  Vinvert  H&VINVERTOSD Bright Screen MenuMenu Position BlankMy Screen Screen MenuStart UP My Screen LockMessage Using the buttons / turns on/off the message functionAuto in Progress while automatically adjusting No Input is Detected Sync is OUT of RangeSearch Reset  CancelOption Menu Auto OFFOption Menu Service GhostFactory Reset FAN SpeedMaintenance LampClaws Case of replacement by yourselfLamp Tabs Center point of claws ClawsApply a vacuum cleaner to the air filter and filter cover Air filterEnglish Internal portion temperature is rising There is no input signalRelated messages Related messages Message DescriptionRegarding the indicator lamps Cooling fan is not operating Regarding the indicator lampsIt is time to clean the air filter There is a possibility that the interior portionPhenomena that may easily be mistaken for machine defects Electrical power cord is not pluggedPower switch is not set to the on position These has not been properly fixedPhenomena that may easily be mistaken for machine defects RGB output SpecificationRGB input Video input Communication portSpecifications
Top Page Image Contents