BOXLIGHT CP-14t manual Lamp Replacement Indicator, Lamp Replacement Monitor Timer

Page 35

APPENDIX

LAMP REPLACEMENT Indicator

When the Lamp of this projector draws to an end, the LAMP REPLACEMENT indicator lights yellow. When the image become dark or the color of the image becomes unnatural, replacement of the Lamp is required.

LAMP REPLACEMENT

CAUTION

●For continued safety, replace with a lamp assembly of the same type.

●Allow the projector to cool for at least 45 minutes before you open the lamp cover. The inside of the projector can become very hot.

●Do not drop the lamp assembly or touch the glass bulb! The glass can shatter and may cause injury.

Follow these steps to replace the lamp assembly.

1

Turn off the projector and disconnect the AC plug. Allow the

projector to cool for at least 45 minutes.

2

Remove a screw with a screwdriver and remove the lamp cover.

3

Remove 2 screws with a screwdriver and pull out the lamp

assembly by grasping the handle.

4

Replace the Lamp Assembly and tighten 2 screws. Make sure

that the Lamp Assembly is set properly. And replace the Lamp

 

Cover and tighten a screw.

5

on.Connect the AC Power Cord to the projector and turn the projector

6

Reset the Lamp Replacement Monitor Timer (refer to the section

“Lamp Replacement Monitor Timer” below.)

NOTE : Do not reset the LAMP REPLACEMENT MONITOR TIMER, when the lamp is not replaced.

LAMP COVER

HANDLE

LAMP

ASSEMBLY

ORDER REPLACEMENT LAMP

Replacement Lamp can be ordered through Boxlight at 1-800-762-5757 or 360-779-7901. ● Model No. of your projector : BOXLIGHT CP-14t

●Replacement Lamp Type No. : POA-LMP19J

(Service Parts No. 610 278 3896)

Lamp Replacement Monitor Timer

Be sure to reset the Lamp Replacement Monitor Timer when the Lamp Assembly is replaced. When the Lamp Replacement Monitor Timer is reset, the LAMP REPLACEMENT indicator stops to lighting.

1

Turn the projector on, and press the MENU button and the ON-SCREEN MENU will appear. Press the POINT

 

LEFT/RIGHT buttons to select SETTING

and press the SELECT button (refer to the page 32). Another

 

dialog box SETTING MENU Menu will appear.

 

2

Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to Lamp age, and then press the

 

SELECT button. The message of "Lamp replace monitor Reset?" is displayed.

3

Select [Yes] to reset the Timer.

 

Do not reset the Lamp Replacement Monitor Timer, except after the lamp is replaced.

35

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Boxlight CP-14t Risk of Electric Shock Do not Open Safety PrecautionsTo the Owner Ground Important Safety InstructionsTable of Contents Compatibility Features and DesignName of Each Part of the Projector PreparationHeight H2 SETTING-UP the ProjectorAdjustable Feet Positioning the ProjectorVentilation Preparation Connecting the AC Power CordPreparation Moving the Projector Terminals of the Projector Connecting the ProjectorVideo Cable Connecting to the Video EquipmentConnecting the Projector IBM-COMPATIBLE Computers VGA / Svga / XGA / Sxga Connecting to the IBM-COMPATIBLE ComputerControl Port Audio Audio OUT Monitor OUT Serial Computer Macintosh Computers VGA / Svga / XGA / Sxga Connection to the Macintosh ComputerAudio Audio OUT Monitor OUT Computer Control PortBefore Operation Operation of the Remote ControlOperating Range of the Remote Control Remote Control Batteries InstallationTOP Controls and Indicators Flow of ON-SCREEN Menu HOW to Operate ON-SCREEN MenuOperating ON-SCREEN Menu Before Operation Menu BAR Turning off the Projector Basic OperationTurning on / OFF the Projector Turning on the ProjectorZoom Adjusting the PictureNo Show Function Basic OperationMenu Operation Sound AdjustmentDirect Operation Automatic Multiscanning system Computer ModeSelecting Computer Mode Selecting Computer SystemPC Adjustment MAC LC13 Compatible Computer SpecificationsAdjust Picture Image Manually Picture Image AdjustmentPosition Auto Image FunctionNormal Function Picture Screen Adjustment Picture Position AdjustmentSelecting Color System Video ModeSelecting Video Mode Wide Adjusting the Picture ImageColor Tint Contrast Brightness Sharpness RegularSelecting Language SettingSetting Menu Appendix Operating Wireless MouseInstallation Controlling Wireless MouseCleaning the Projection Lens MaintenanceTemperature Warning Indicator AIR Filter Care and CleaningLamp Replacement Monitor Timer below Lamp Replacement IndicatorLamp Replacement Lamp Replacement Monitor TimerTroubleshooting Turn the projector on before you turn on the computer Check the mouse setting on your computerCheck the batteries Maximum operating range is 16.4 feet 5mTechnical Specifications Optional Parts Limited Warranty
Top Page Image Contents