BOXLIGHT CP-14t manual Connecting the Projector, Terminals of the Projector

CONNECTING THE PROJECTOR

TERMINALS OF THE PROJECTOR

COMPUTER INPUT TERMINAL	MONITOR OUTPUT TERMINAL
Connect the computer output	Connect the monitor to this
to this terminal.	terminal.
(Refer to P12 ~15.)	(Refer to P12 ~15.)

CONTROL PORT CONNECTOR
When controlling the computer	COMPUTER IN		MONITOR OUT
with the Remote Control of this
projector, connect the mouse
port to this connector.	CONTROL PORT
(Refer to P12 ~15.)			SERIAL
	AUDIO IN		AUDIO OUT
COMPUTER AUDIO INPUT JACK			▼ S-VIDEO
	R–AUDIO–L
Connect the audio output from		VIDEO
the computer to this jack.
(Refer to P12 ~15.)	(MONO)

SERIAL PORT CONNECTOR

This connector is used to connect a computer to control this projector with the PC.

(Refer to P12 ~13.)

AUDIO OUTPUT JACK

Connect the audio amplifier to this jack.

(Refer to P12 ~15.)

RESET BUTTON

This projector uses a micro processor to control the unit. Occasionally, the micro

AUDIO INPUT JACKS

Connect the audio outputs from the video equipment to these jacks.

(Refer to P11.)

●When the audio output is monaural, connect it to the AUDIO LEFT jack.

VIDEO INPUT JACK

Connect the video output from the video equipment to this jack.

(Refer to P11.)

S-VIDEO INPUT JACK

Connect the S-VIDEO output from the video equipment to this jack.

(Refer to P11.)

processor may malfunction and need to be reset. This can be done by pressing the RESET button with a pen, which will shut down the unit. Turn the projector off and restart the unit. Do not use the RESET function excessively.

COMPUTER INPUT / MONITOR OUTPUT TERMINAL

1 Red Input 9 Non Connect

Terminal : HDB15-PIN

Connect the display output terminal of the computer to this COMPUTER INPUT with the VGA Cable (supplied), and connect the monitor to this MONITOR OUTPUT with the monitor cable (not supplied). When connecting the Macintosh computer, the MAC Adapter is required (not supplied).

Pin Configuration

5 4 3 2 1

10 9 8 7 6

15 14 13 12 11

2	Green Input	10	Ground (Vert.sync.)
3	Blue Input	11	Sense 0
4	Sense 2	12	Sense 1
5	Ground (Horiz.sync.)	13	Horiz. sync.
6	Ground (Red)	14	Vert. sync.
7	Ground (Green)	15	Reserved
8	Ground (Blue)

CONTROL PORT CONNECTOR	Pin Configuration
Terminal : MULTI-POLE 12-PIN
When controlling the computer with the		2	1
projector's Wireless Remote Control Unit,
	6	5	4	3
connect control port (PS/2, Serial or ADB port)	10	9	8	7
on your computer to this connector. (Control		12	11

Cable for PS/2 Port is supplied.)

SERIAL PORT CONNECTOR	Pin Configuration
Terminal : DIN 8-PIN
This connector is used to connect a computer	8	7	6
to control the projector with the PC. For this
	5	4	3
connection, the Serial Cable is required (This	2	1

cable is not supplied).

	PS/2		Serial		ADB
1	-----		T X D	-----
2	CLK		-----		ADB
3	DATA		-----	-----
4	-----		-----	-----
5	-----		R X D	-----
6	-----		-----	-----
7	-----		READY	-----
8	-----		-----	-----
9	GND		GND		GND
10	-----		-----	-----
11	-----		-----	-----
12	-----		-----	-----
1		R x D			5	MUXTTL
2		ADB			6	T x D
3	MUX232				7	–––––
4		GND			8	–––––

10