Black Box LC-XE10 Basic Operation, Turning On the Projector, Turning Off the Projector

Page 19

Basic Operation

Turning On the Projector

1

Complete peripheral connections (with a computer, VCR, etc.)

 

before turning on the projector.

2

Connect the projector's AC power cord into an AC outlet. The

 

POWER indicator flashes red in a moment and turns on red.

3

Press the POWER ON-OFF button on the top control or on the

remote control. The POWER indicator turns green, and the

 

cooling fans start to operate. The preparation display appears on

 

the screen and the count down starts. (A captured image can

 

be used as the preparation display. See “Capture” on page 40.)

4

After the count-down, the input source that was selected last

 

and the Lamp mode status icon appear on the screen.

26

The preparation display disappears after 30 seconds.

Selected Input Source and Lamp Mode

Lamp mode

(See page 41 for Lamp mode.)

Turning Off the Projector

1

Press the POWER ON-OFF button on the top control or on the

remote control, and a message "Power off?" appears on the

 

screen.

2

Press the POWER ON-OFF button again to turn off the

projector. The POWER indicator starts to flash red, and it

continues while the cooling fans are operating (for about 90 seconds).

3

When the projector has cooled down enough to be turned on

again, the POWER indicator lights red. Then you can disconnect

the AC power cord.

TO MAINTAIN THE LIFE OF LAMP, ONCE YOU TURN PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE TURNING IT OFF.

DO NOT DISCONNECT AC POWER CORD WHILE COOLING FANS ARE RUNNING OR BEFORE POWER INDICATOR LIGHTS RED. OTHERWISE IT WILL RESULT IN SHORTENING LAMP LIFE.

The message disappears after 4 seconds.

NOTE

●The projector cannot be turned on during the cooling period with the POWER indicator flashing red. You can turn it on again after the POWER indicator lights red.

●When the On start function is on, this projector is turned on automatically by connecting the AC power cord to an AC outlet. (See page 41 for the On start function.)

●Do not use the projector for more than 24 hours continuously. Turn off the projector at least once in 24 hours and give it a rest. Continuous use may result in shortening the lamp lifetime.

●This projector monitors internal temperature and automatically controls the running speed of the cooling fans.

●If the WARNING indicator flashes or lights red, see “Warning Indicator” on page 43.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Model LC-XE10 Table of Contents Risk of Electric Shock Do not Open To the OwnerVoor de klanten in Nederland Safety InstructionsMoving the Projector Safety InstructionsInstalling the Projector in Proper Position Air CirculationFederal Communication Commission Notice Compliance200 240 V AC ComplianceFor Continental Europe For the U.S.A. and CanadaFeatures and Design Front Back Bottom Part Names and FunctionsTerminal Part Names and Functions1!2 TopZoom Freeze Remote ControlPointer Function Laser Pointer FunctionWireless Mouse Operation Remote Control CodeRemote Control Batteries Installation Remote Control Operating RangeAdjustable Feet InstallationPositioning the Projector Connecting to a Computer InstallationTerminals Projector Video Source example Connecting to Video EquipmentTurning On the Projector Basic OperationTurning Off the Projector Basic Operation Zoom AdjustmentFocus Adjustment Keystone AdjustmentPicture Freeze Function Auto Set Up FunctionKeystone correction Corner Direct Operation Timer FunctionSound Adjustment No Show FunctionOn-Screen Menu Remote ControlOn-Screen Menu Top ControlMenu Bar Input Source Selection Computer InputMode Computer InputComputer System Selection AutoTo store adjustment data Computer Adjustment AutoAuto PC Adj Computer Adjustment Manual To clear adjustment data ResetMode free Display area To store adjustment dataImage button Standard Real Image Level SelectionStandard RealImage Level Adjustment Screen Size Adjustment Input Source Selection Video, S-Video, Y, Pb/Cb, Pr/Cr Video InputPb/Cb, Pr/Cr Input button Computer Video Computer 2 button Video InputInput Source Selection RGB Scart 21-Pin RGB ScartAV System Menu Video or S-Video Video System SelectionVideo or S-Video ComponentImage button Standard Cinema CinemaTint ColorProgressive Resets all adjustment to their previous figure Setting SettingSetting Pointer Power managementLamp mode On startTo change the code for the projector To change the code for the remote controlWireless Mouse mode Projector modeProjector is shut down and the Warning indicator lights red Maintenance and CleaningThen check the items below Cleaning the Projector Cabinet Maintenance and CleaningCleaning the Air Filters Cleaning the Projection LensReset the Lamp replace counter Lamp ReplacementLamp Replace Counter Lamp Handling PrecautionsAppendix TroubleshootingAppendix Projector Condition Indicators and Projector ConditionInput PC AdjustImage Adjust Screen Menu TreeSound System SettingImage Adjust Image SelectFreq Compatible Computer SpecificationsKHz Technical Specifications Terminal HDB15-PIN Pin Configuration Configurations of TerminalsTerminal DVI-I Pin Configuration Optional Parts Attaching the Lens Cover Off Projector is not locked with USB Key On1 Key registrationDeleting key registration To lock the projector with USB keyAppendix Appendix Key to better communications Canada
Top Page Image Contents